How should dairy cattle manure be modeled for United States systems?

02 June 2020 0 2K Report

Looking for suggestions for processed based dairy manure modeling approaches at a high level of aggregation.

Badges
Science topic

More Hector Menendez's questions See All

Can anyone recommend an antibody development course?

I would like to find a short course focused on the development of monoclonal antibodies covering the entire process, from the selection of antigen and carrier, to the purification of the final...

27 June 2024 5,618 1 View

How can I improve my electrophoresis technique?

Hello. I'm making non-denaturing PAGE of DNA fragments for analysis of polymorphisms, but I'm getting wavy bands. If somebody can help me, I will be very greatful. First of all, here's my recipe...

15 March 2024 7,699 1 View

Does anyone know if it is possible to calculate amorphous phases in weight percent in a whole rock geological sample using Bruker Topas software?

Does anyone know if it is possible to calculate amorphous phases in weight percent in a whole rock geological sample using Bruker Topas software? I have a sample whole rock sample that has about...

16 January 2024 8,806 5 View

Why covalent conjugation with latex particles?

For latex nanoparticles, conjugation to proteins can be done either covalently or non-covalently. The covalent method is usually long (days) and complex (NHS, cabodiimides, etc), but the...

02 October 2023 6,114 2 View

Do you have good references for protein precipitation with PEG?

I am trying to find at least 1 good article that describes clearly the molecular mechanism behind protein precipitation with PEG6000. For some reason I'm not able to find thin information clearly...

25 September 2023 5,084 4 View

Does refactoring mean that you modify the entire design iteratively?

It is posible refactoring and no modify they entire design iteratively?

19 June 2023 6,836 3 View

Tips on cryopreserving HEK293T?

Dear friends, I am planning to cryopreserve and generate a HEK293T cell bank, but I have a few doubts on how to achieve best results. I am using "Corning® CoolCell® FTS30 container" for the...

31 May 2023 8,539 2 View

DMEM (1X) + GlutaMAX temperature degradation?

Hi guys, I was wondering what effect would have a slight temperature increase in my cell culture media. The PID controller of our reactor didn't work as expected and the temperature process...

23 May 2023 292 0 View

Anything about fashion photography?

I need informations about the history of fashion Images including illustrations and fashion photography.

01 April 2023 7,609 2 View

Would the age of mice (young versus old) affect the growth of subcutaneous tumour models?

I would like to know if anyone has experience in regards of subcutaneous tumour models and whether the age of the mice may affect the rate of growth of the tumour. Would the immune system,...

15 March 2023 9,045 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to enrich pig excreta for increasing nutrient quality organically ?

Pig slurry is rich in major and minor nutrients. Is there any way to improve / Enrich its manure quality to be used in agriculture organically ? please share your knowledge.

09 August 2024 5,605 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View