How can I find nodes with specific displacement in Odb with python?

Hi every body I have some explicit analysis on plate under impactor. I need to extract the damaged elements in end of analysis with using python. who can explain this for me?

07 August 2019 7,334 2 View

Why for a thick steel plate , Ultimate compressive strength over than "1" ?

Hi I have modeling the steel plate with thickness 28 mm, and slenderness ratio same as 1( L=2.4,B=0.8 m). the model post buckling under uni-axial loading analysis with Abaqus/Riks method. the...

08 September 2018 3,386 6 View

How can i delete shell element in abaqus?

I make a shell model in abacus and mesh it. how can I **delete some elements** in this model?

04 May 2018 1,028 4 View

How can i defign and apply PBC on plate edges for compression load on other edges?

Hi I try to model a plate with in-plan loading for analysis of post-buckling. for some configuration of longitudinal stiffeners like as symmetrical stiffener section, the BC of long edges of plate...

03 April 2018 4,425 7 View

What is my mistake in my tnt explosion modeling with ABAQUS?

If you read the Kevorkian paper(attached), the over-pressure in experiment about 60bar at K4 sensor. But in my model (attached) with CEL technique, this pressure is near 20 bar. so,if you know,...

31 December 2017 9,919 1 View

Who know about considering chapman-jouguet pressure in tnt air explosion modeling?

HI HOW CAN I CONSIDER THE "CHAPMAN JOUGUET" PRESSURE IN ABAQUS MODELING FOR TNT AIR EXPLOSION?

11 December 2017 3,842 3 View

Is Johnson cook parameter are available for ST-37 STEEL?

ANY BODY HELP ME ABOUT THIS PARAMETERS: ST-37 STEEL JOHNSON-COOK FAILURE PARAMETERS...

10 November 2017 5,991 0 View

How can I model heat and tempreature in TNT-AIR-Steel plate explicit analysis with abaqus?

I've been try to model explosion of TNT in Air(Eulerian model) and steel plate(Lagrangian) for finding the plate central node displacement and compare with Conwep blast analysis result. without...

07 August 2017 2,806 1 View

How can I extract a part from analysis at some step in abaqus?

Hi I model a dynamic analysis and i will off a part at a moment in my analysis.how can I run this condition?

06 July 2017 965 0 View

How can I remove non contact elements in a damaged part?

02 March 2017 5,289 0 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View