How can i remove the error bar from the legend?

xdata1=tempmeasS2.Timesec; ydata1=tempmeasS2.UCNP; plot (xdata1,ydata1) err2 = tempmeasS2.UCNP1; e2=errorbar(xdata1,ydata1,err2, 'b-', 'lineWidth', 1, 'HandleVisibility', 'on') legend ('1...

13 January 2021 3,140 3 View

How to prepare 0.03M phosphate buffer pH:4.0?

I want to prepare mobile phase has to be adjusted to pH 4 with o.03M phosphate buffer Can anyone help me to prepare phosphate buffer solution of 0,03M using pH of 4 ? waiting for your favorable...

18 November 2020 210 3 View

How to prepare 0.035M phosphate buffer pH:4.5?

I want to prepare mobile phase has to be adjusted to pH 4.5 with o.035M phosphate buffer Can anyone help me to prepare phosphate buffer solution of 0,035M using pH of 4.5 ? waiting for your...

18 November 2020 3,384 1 View

What is the most reliable method for starch digestibility analysis in beans?

I found papers cited Englyst et al. (1992) and mentioned Megazyme kit, But unfortunately these were not clear and hard to follow. Thanks in advance,

23 September 2020 1,476 5 View

What is the reason of spongy structure of nanocellulose after freeze drying step?

To obtain dried powder nanocellulose, we used freeze drying method but the result is nanocellulose sponge not powder. Could we have failed because the acid was not sufficiently removed from the...

05 January 2020 6,277 2 View

Have you ever used OCAI organizational culture assessment tool?

I would like to use Competing Values Framework organizational culture assessment tool OCAI for my research and need some advice about its Likert version. I would be glad to hear the experiences of...

14 November 2017 3,467 2 View

Why do we calculate negative encapsulation efficiency in plga nanoparticle?

Hello, I need to help about my thesis. I syhnthesize catechin loaded plga nanoparticle. I use indirect analysis method for calculate encapsulation efficiency and I get negative encapsulation...

06 November 2016 2,464 4 View

Why my agarose gels drop off in neutralization buffer during alkaline comet assay?

21 June 2016 839 12 View

What is the normal range of fasting serum insulin in rats?

What is the normal range of fasting serum insulin in rats? I could'nt find any range mlU/L?

04 June 2016 9,616 9 View

Is there anyone to merge DAPI-Tunel images?

27 January 2016 7,240 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Genescan gives 3 peaks instead of one?

Hi all, I am doing a genescan analysis for a deleted exon in the patient sample. The amplified region is 215 bp. In the patient sample because of homozygous deletion, no peak is observed while in...

23 February 2021 5,645 1 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View