How can i create a moving harmonic load in ANSYS workbench?

More Hajar Rhylane's questions See All

Which software is better to write systematic review paper?

We have seen some authors use some software to write review paper. As obvious, the study of all published papers concerning our studying field is not possible and these software can help us to...

27 February 2021 6,296 1 View

Reaction condition to convert NH2 to COOH?

I need to couple Dopamine by NH2 end to silica nanoparticles coated by PEG-NH2, but first i need to convert the PEG-NH2 to COOH by using succinic anhydrous ... can you suggest a reaction condition ?

13 February 2021 2,768 4 View

Surface modification of silica nanoparticles with PEG?

I'm trying to coat my silica NP with diamine PEG, so i used GOPTS to add epoxy group on the surface of the NP then i'll add the PEG. I can not found protocol for SiNP coating PEG, most of the...

13 January 2021 4,915 4 View

Silica nanoparticles synthesis using Stober method with size rang 30-50 nm?

I'm preparing silica NP controlling the size by using different concentration of NH4OH. 1- 16.75 ml ethanol. 2-0.5 ml TEOS. 3- NH4OH (0.3- 0.5- 0.75- 1 ml) mixed for 24 hr then evaporate the...

27 November 2020 1,504 13 View

Which neuronal cell line contain D1R?

I'm formulating a drug delivery system that could stimulate Dopamine receptor, For that i need to choose cell line that contain D1R and could be simulated using my delivery system... I have read...

20 November 2020 9,104 2 View

Problems in PCR using Folmer primers, can you help please ?

Hello, I'm using the classic Folmer LCO1490 and HCO2198 primers for a venerid bivalve ADN for two months but the results are still negative, I can't see the bands. 1. I tried to change the...

03 November 2020 9,190 3 View

How to culture prokaryote and eukaryote from the gut of marine organism?

Info regarding the type of media and culturing condition would be really appreciated. Thanks

21 July 2020 6,937 1 View

Calculating sample size for a multivariate regression in GPOWER?

Hello I currently have two dependent variables (with 4 measurements each) and two independent variables My question is how to calculate the sample size using Gpower for multivariate multiple...

21 November 2018 5,719 2 View

CDNA conc. for RT-PCR?

what is the recomended conc. to prepar cDNA to run rt-pcr for brain rat tissue.. i used 50ng/ul some primer gave ct value btw 20-22 but other above 30.. ?

30 October 2017 7,016 3 View

How do i increase the RNA 260/230 ratio ?

i did RNA extraction using differnt protocol triazol and invetrogen RNA mini kit .. the 260/280 ratio was 1.9 to 2.1 but for the 260/230 i got 1.5 to 1.8 in both protocols, should i consider it...

29 October 2017 4,780 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Sajid Ahammed

Hajar Rhylane please go through the following tutorial attached herewith ,

https://youtu.be/Mofu3Ux21kE

https://youtu.be/S-JScTVBHXQ

hopefully it will help you. Thank you

Hajar Rhylane

thank you, sir Sajid Ahammed for your answer but the video shows the case of stationary harmonic load while in my case i need to know how to create a moving harmonic load in ANSYS.

Hajar Rhylane same procedure just need to use moving mesh.