My aim is to study the micro-structural changes in compacted bentonite for different moisture contents w.r.t time.For that I need to conduct SEM. So, please suggest the precautions I need to consider while preparing samples, drying processes etc.
Either freeze-drying and then standard observation (with conductive coating) or environmental SEM (with a peltier stage).
Cryo-preparation might be a further alternative....
Does anyone have experience isolating microRNA from isolated mitochondria for sequencing?
21 June 2023 3,146 0 View
Interested to know if there is any relationship between 1. Tuberculosis and Myocardial Infarction 2. Tuberculosis and COVID-related mortality cases?
11 July 2022 5,018 2 View
ρ∂u/∂t+ρ(u.∇)=∇.[-pI+K]+F I need to add -∂/∂_x (ρU_0 u_j ) this term in all three coordinates instead of F
08 July 2022 480 1 View
Please provide formulas to find parameter fracture strain, Displacement at failure, Stress triaxiality, Strain rate.. Thanks in advance
28 April 2022 112 2 View
I am performing miRNA loss-of-function study in cells and using a reporter assay to validate miRNA inhibition. So, I am planning on cloning the entire 3’-UTR sequence of our miRNA target...
08 August 2021 7,247 3 View
Iam getting these errors when iam analysing AMOVA in Arlequin 1 #[ERROR # 1] from function "Population::New_read_genotypic_data()" : phenotypes have different number of loci 2 #[ERROR # 2] from...
26 April 2021 8,835 3 View
Hi, I am modeling wave propagation in a composite plate using inbuilt PZT-5H. In my model, a signal is actuated at a PZT which is attached to the composite and the wave propagates through the...
16 April 2021 6,071 0 View
I changed new primers and water and anealing temperature but i didn't get results?
11 September 2018 3,639 3 View
I was reading through this article. Just felt very bad about the contents which are published by some journals. Looks like there is a lot of garbage, which needs to be identified and...
22 December 2017 3,585 25 View
My project is on Analyzing the Ageing effects of expansive clay soil ; Micro-structure approach.For this, I need to perform Scanned Electron Microscopy(SEM) and Mercury Intrusion Porosimetry...
27 November 2015 3,158 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...
07 August 2024 5,343 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View