How can I change outflow boundary condition to convection boundary condition in ANSYS FLUENT ?

More Aniruddha Sanyal's questions See All

How do you evaluate the Transformative journal in Elsevier portal?

In recent year, Elsevier changes its policy for several hybrid journal to a new agreement policy of journal with the potential funding authorities (such as the University of Florida, Carnegie...

12 January 2021 6,034 2 View

Cite score is not considered during calculating Impact factor?

Cite score is a similar indicator for calculating the average citation per published paper through the Scopus database; whereas, the Impact Factor (IF) was calculated through JCR (Journal citation...

30 November 2020 8,861 3 View

How to derive parametric equations from a given dataset by Gene Programming Method ?

I have a dataset of some dependent and independent variables. How to get a parametric equation from this. In some paper, it is written that they have created equation from Gene programming method....

24 July 2020 6,979 2 View

Can you suggest the simplest protocol for microplastics determination in soil and air samples?

Dear Fellow and peers, I am looking for any established protocol for extraction and determination (quantitative and qualitative) of microplastics in soil and air dust samples. If you have any...

18 July 2020 4,751 1 View

How to decide the proper number of elements in edge sizing for tetrahedral meshing ?

For hexahedral meshing, it is quite simple to divide one edge in a particular number of division. But for tetrahedral meshing it is not that simple. If we are using a complicated domain for...

29 June 2020 4,137 6 View

Is it possible to create an analytical expression from the artificial neural network toolbox in MATLAB?

Is it possible to create an analytical expression from an artificial neural network toolbox in MATLAB? If not, then how can these datasets be used as objective function in optimization? In some...

10 June 2020 5,753 8 View

How to plot the graph of turbulence intensity in ansys cfx for steady state analysis??

I want to plot the graph of turbulence intensity vs height of domain. How to do that in Ansys cfx for steady state analysis?

20 April 2020 1,993 3 View

What will be the analytical solution for two-dimensional unsteady-state heat conduction equation for a cylindrical pipe/rod (cylindrical coordinates)?

Is there any article that provides good insight on the procedure for reaching an analytical solution of this problem, especially when heat is applied at the wall of the cylindrical pipe and the...

04 March 2020 9,092 7 View

Why unexpected peak before the standard pesticide peak in HPLC?

I worked with procymidone and its metabolites for residue analysis in fruits and vegetables. But, when I injet the stardard vials of procymidone for the calibration curve there is a giant...

26 September 2019 3,286 6 View

Can someone please suggest a circuit to prevent back powering in jtag connections when working with FPGA devices?

I need some clarity on this topic as to how we can implement jtag protection while programming/debugging FPGA circuit.

28 February 2019 6,070 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Mohammad Malekan

Dear Aniruddha,

You need to interpret your UDF first, using the "interpreted" tool in user defined menu. Then, at the boundary condition edit window you can choose to have either a constant value or user defined function, defined by the UDF file, for your boundary condition.

Hope it helps,

Regards,

Panayampilly abubucker abdul samad

Can you post UDF?