Cart3D Tool in ICEM CFD Ansys 14.5
Ansys Inc has give up the cart3D software
As we know there are numerous components and systems in Ansys workbench, such as Ansys Fluent, CFX, etc etc. But I only want to perform static structure analysis and want to buy a package that can...
09 October 2016 7,171 4 View
I am thinking of simulating the flow of water on a tank through holes at the bottom. It can be hand calculated to estimate the time required to drain out the water but I want to do some CFD on...
03 April 2015 5,676 9 View
I am trying to find if there is an analytical or simpler way to find pressure or force acting on the upper surface of a wing due to the gust wind. Assuming the wing is not in motion (static case)...
01 February 2015 2,595 5 View
I am trying to think of simple general modifications that can be done to a conventional type UAV so that it flies with better stability during crosswind of about 13m/s.
31 December 2014 2,839 13 View
I'm trying to simulate flow through a regulator to check at what position the outlet has 1000 psi (Fig attached). The inlet pressure (static) is 2,800 psi. I can measure experimentally the static...
31 December 2014 9,582 13 View
What is a floating boundary condition in CFD? In what condition can I use it? I suppose such a BC exists only in few commercial packages. Are there any other BCs equivalent to a floating BC in...
08 September 2014 6,957 5 View
I have a case where I need to perform some CFD simulations. There is a mixture of water and sludge in a water reservoir which flows through a pipe installed at the bottom and then past a...
07 August 2014 8,274 24 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...
02 July 2024 6,293 0 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...
25 June 2024 4,286 4 View
I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.
24 June 2024 5,125 0 View
I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.
20 June 2024 1,668 0 View