Has anyone tried Cart3D in ICEM CFD Ansys 14.5? I can't seem to find the option in the toolbar there?

Cart3D Tool in ICEM CFD Ansys 14.5

06 July 2015 3,507 1 View

Is it possible to perform CFD for flows without an inlet?

I am thinking of simulating the flow of water on a tank through holes at the bottom. It can be hand calculated to estimate the time required to drain out the water but I want to do some CFD on...

03 April 2015 5,603 9 View

Which is the analytical approach for finding the pressure acting on a surface due to velocity?

01 February 2015 2,490 5 View

Do you have any design consideration for a UAV for flying against crosswind?

I am trying to think of simple general modifications that can be done to a conventional type UAV so that it flies with better stability during crosswind of about 13m/s.

31 December 2014 2,728 13 View

What boundary conditions to set in Fluent when I know only the static pressure at Inlet and outlet?

31 December 2014 9,397 13 View

What is a floating boundary condition in CFD?

08 September 2014 6,831 5 View

Multi-phase flow or single-phase flow for a mixture of water and sludge?

07 August 2014 8,158 24 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View