a master plan for glass factory
I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...
28 February 2021 4,851 8 View
the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please
16 February 2021 8,801 3 View
I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...
11 February 2021 2,193 6 View
I need to know the reliability of the evaluation results and the rate of achievement of the course objectives, Thank you (*-*).
02 February 2021 7,828 7 View
I need to know the extent of the success of the e-learning plan in countries of different capabilities, Thank you (*-*)
02 February 2021 4,712 15 View
Hi Dear colleagues This was my first experience on SSCP, and I couldn`t get any band by silver staining! Staining with Et Br was successful. I mixed the PCR product with formamide loading dye,...
01 February 2021 8,788 6 View
I could not synthesize Selenium nanoparticles by PEG 200 at up-scale ( more than 100 ml) as it got aggregated while at small amounts it works fine , I work with 850 PPM using selenium powder in...
08 January 2021 10,049 1 View
I want to solve the following matrix equation with respect to the matrix variable X which is a real symmetric positive definite matrix. The given matrix A is real and symmetric, "a" is a scalar,...
04 January 2021 2,945 7 View
i built the structure of the organic solar cell (ito-P3HT_PCPM-PEDOT_PSS-al) then i used BEAM statement to add sunlight so what is the best method to add nanoparticles in layers
03 January 2021 7,107 11 View
I am simulating a single flow in a 2D tube with a uniform heat flux applying on the outer surface. I found difficulties finding the Nusselt Number or in other words a correct way to obtain...
26 December 2020 4,054 7 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...
27 February 2021 6,801 3 View
I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium
24 February 2021 1,915 1 View
I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...
23 February 2021 6,043 1 View
I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.
21 February 2021 5,465 4 View
I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...
18 February 2021 5,319 3 View
The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...
18 February 2021 9,538 1 View
Regarding my needs I am looking for a glass coating agent that makes the glass hydrophobic permanently
09 February 2021 3,924 5 View
A certain protocol we have developed requires the use of a Rocker/Rocking Shaker in which our dishes with cells are maintained in the incubator. The rocking is essential to the protocol but we...
09 February 2021 3,291 1 View
