Fabrication of TFT

More Ashutosh Kumar Dikshit's questions See All

In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

What condition required for coating of Fe3O4@SiO2 by using APTES?

I tried coating Fe3O4@ SiO2 by using APTES in 5% water-ethanol but it is not coated. Kindly suggest a solution for it. Thanks

24 February 2021 5,992 4 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

ZnS oxidizes to ZnO!!why??

when I put my ZnS solution in the chemical bath, the ZnS oxidizes so there are ZnO peaks appearing because of the reaction with the oxygen in the air, despite the fact that I close the beaker...

14 February 2021 5,778 9 View

I want to remove TiO2 and SiO2 coating from surface. any one can help me?

I want to remove TiO2 and SiO2 coating from surface. I think that i should use HCl and MgCl2 and an oxidation agent such as potassium nitrate, but i dont know in which propertion should these...

14 February 2021 300 3 View

How to prepare OH- terminated Si Wafer?

Hi, Folks. I am working on the ALD project to deposit Al2O3 on the Si wafer from TMA and Water. I have struggled with the preparation of OH- terminated Si wafer. I have both Si(1 0 0) and...

08 February 2021 8,792 2 View

Having 2 different substrates under the same deposit conditions (TiN coating) why it is possible to obtain different colours in the 2 dif substrates?

Coating is made by same deposit conditions. substrates are HSS Drill bit and Shim SS 300 series. On the drill bit we are getting some golden color, however on the shim we got no color it is like...

08 February 2021 9,383 7 View

Xrd result of ZnO thin film shown better crystallinity at low temperature and the crystallinity decreases as the temperature increased. why?

I have synthesized ZnO thin films at four different substrate temperature say, 300, 350, 400 and 450C. and the samples were annealed at 450C for half an hour. the xrd result shown better...

04 February 2021 7,641 4 View

Mir Waqas Alam

What you mean by I_V Characteristics is no?

If getting low current or straight line than may be you have short in electrodes. Check the mask alignment for electrodes and each other films..

Kiesar Sideeq Bhat

Please refer to this article:

Article Nozzle-jet printed flexible field-effect transistor biosenso...

Satyendra Kumar Mourya

Dear Ashutosh, your question is not clear to me. What kind of difficulties are you facing? Is it related to fabrication or characterization?