Does anyone have an idea or research about embrittlement temprature range of AISI 4140 steel??

08 August 2017 0 500 Report

And an special heat treatment for modifying tensile strength and impact energy of this alloy?

Badges
Science topic

More Hossein Ahmadi's questions See All

Is there a process for changing crystalline silicon nanostructures or nanoparticles to amorpous silicon which is going to be used in Li ion batteries?

Amorphous silicon has lower volumetric change than crystalline silicon during first cycles of charge and discharge. How can we prepare amorpous silicon from nanostructured crystalline silicon? Is...

10 November 2019 2,569 4 View

How to clean copper surface before coating process?

What are suitable reagents for removing oxide layer and grease or organic impurities from copper surface before the coating process?

07 August 2019 3,061 4 View

How to leach Fe impurities out of Silicon Suspension?

High energy ball milling used to prepare silicon micro and nano particles. I used magnetic separation to remove iron. But there is a small amount of iron left in the suspension. How can I remove...

06 July 2019 4,438 2 View

What are suitable reagents for color eching of AISI 304 stainless steel?

Any reagent for revealing microstructure, electroetching, chemical etchin, or other methods. I need the colorful microstructure image. I only need the artistic aspect of images!

06 July 2019 6,317 3 View

How to calculate density of a coating layer?

It's a coating with few micrometers in thickness. There are equations for thickness prediction. But for using them, I need to know the coating density. I'm using spray coating method. The...

06 July 2019 7,006 4 View

What are flow lines?

Does anyone knows a reference book that describes this phenomena? Are flow lines and shear bands the same or they're different from each other? why flow lines appear in micro structure? (Attached...

01 February 2018 3,291 0 View

Why second phase particles cluster during cold work?

In the attached picture, rolling direction is from bottom to the top(vertical).

01 February 2018 2,033 0 View

Can grain structure be revealed using SEM?

can we see the grains and grain boundaries without using any etching procedure by SEM?

11 December 2017 8,141 2 View

What is the main reason for edge cracking of aluminum alloys during cold rolling?

sheet edge geometry change, workability limitation or something else?? Does anyone have studied about that?

09 October 2017 4,727 3 View

Can Quench and Partitioning heat treatmnet(Q/P) improve the impact energy of AISI 4140 steel?

08 September 2017 3,583 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Can anyone explain why there is not any color bands in the middle portion of the tensile coupon?

Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)

03 August 2024 8,538 4 View