How to leach Fe impurities out of Silicon Suspension?

More Hossein Ahmadi's questions See All

Is there a process for changing crystalline silicon nanostructures or nanoparticles to amorpous silicon which is going to be used in Li ion batteries?

Amorphous silicon has lower volumetric change than crystalline silicon during first cycles of charge and discharge. How can we prepare amorpous silicon from nanostructured crystalline silicon? Is...

10 November 2019 2,401 4 View

How to clean copper surface before coating process?

What are suitable reagents for removing oxide layer and grease or organic impurities from copper surface before the coating process?

07 August 2019 2,913 4 View

How to calculate density of a coating layer?

It's a coating with few micrometers in thickness. There are equations for thickness prediction. But for using them, I need to know the coating density. I'm using spray coating method. The...

06 July 2019 6,846 4 View

What are suitable reagents for color eching of AISI 304 stainless steel?

Any reagent for revealing microstructure, electroetching, chemical etchin, or other methods. I need the colorful microstructure image. I only need the artistic aspect of images!

06 July 2019 6,161 3 View

What are flow lines?

Does anyone knows a reference book that describes this phenomena? Are flow lines and shear bands the same or they're different from each other? why flow lines appear in micro structure? (Attached...

01 February 2018 3,036 0 View

Why second phase particles cluster during cold work?

In the attached picture, rolling direction is from bottom to the top(vertical).

01 February 2018 1,905 0 View

Can grain structure be revealed using SEM?

can we see the grains and grain boundaries without using any etching procedure by SEM?

11 December 2017 7,982 2 View

What is the main reason for edge cracking of aluminum alloys during cold rolling?

sheet edge geometry change, workability limitation or something else?? Does anyone have studied about that?

09 October 2017 4,589 3 View

Can Quench and Partitioning heat treatmnet(Q/P) improve the impact energy of AISI 4140 steel?

08 September 2017 3,443 0 View

Does anyone know the best temperature for quench and best temperature for partitioning in Quench and Partitioning heat treatment of AISI 4140 steel?

I need to achieve maximum impact energy and hardness at the same time.Any experiment or reliable article??

08 September 2017 9,764 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

What solvent can I used for Paal Knorr reaction between 6-amino hexanoic acid and 2.5 hexanedione?

I am try to make the Paal Knorr reaction between 2.5 hexnedione and 6-amino hexanoic acid, my problem is type of solvent to use, because 6-hexaminohexanoic acid is soluble in water but I am not...

02 March 2021 4,443 2 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View

Can water be extracted from Olivine?

I have always been interested in geology and wondered about how unique structures of materials behave in different circumstances. I stumbled upon Olivine, the magnesium iron silicate, and heard...

28 February 2021 7,330 4 View

I want to performe MALDI-TOF MS for bacterial identification, I would appreciate it if anyone can tell me the matrix solution preparation protocol ?

based on what I've studied on multiple papers, for peptide and protein identification Alpha-cyano-4-hydroxycinnamic acid (CHCA) is an appropriate matrix to use, I also know that the CHCA powder...

26 February 2021 6,799 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View