Can grain structure be revealed using SEM?

More Hossein Ahmadi's questions See All

Is there a process for changing crystalline silicon nanostructures or nanoparticles to amorpous silicon which is going to be used in Li ion batteries?

Amorphous silicon has lower volumetric change than crystalline silicon during first cycles of charge and discharge. How can we prepare amorpous silicon from nanostructured crystalline silicon? Is...

10 November 2019 2,569 4 View

How to clean copper surface before coating process?

What are suitable reagents for removing oxide layer and grease or organic impurities from copper surface before the coating process?

07 August 2019 3,061 4 View

How to leach Fe impurities out of Silicon Suspension?

High energy ball milling used to prepare silicon micro and nano particles. I used magnetic separation to remove iron. But there is a small amount of iron left in the suspension. How can I remove...

06 July 2019 4,438 2 View

What are suitable reagents for color eching of AISI 304 stainless steel?

Any reagent for revealing microstructure, electroetching, chemical etchin, or other methods. I need the colorful microstructure image. I only need the artistic aspect of images!

06 July 2019 6,317 3 View

How to calculate density of a coating layer?

It's a coating with few micrometers in thickness. There are equations for thickness prediction. But for using them, I need to know the coating density. I'm using spray coating method. The...

06 July 2019 7,006 4 View

What are flow lines?

Does anyone knows a reference book that describes this phenomena? Are flow lines and shear bands the same or they're different from each other? why flow lines appear in micro structure? (Attached...

01 February 2018 3,291 0 View

Why second phase particles cluster during cold work?

In the attached picture, rolling direction is from bottom to the top(vertical).

01 February 2018 2,033 0 View

What is the main reason for edge cracking of aluminum alloys during cold rolling?

sheet edge geometry change, workability limitation or something else?? Does anyone have studied about that?

09 October 2017 4,727 3 View

Can Quench and Partitioning heat treatmnet(Q/P) improve the impact energy of AISI 4140 steel?

08 September 2017 3,583 0 View

Does anyone know the best temperature for quench and best temperature for partitioning in Quench and Partitioning heat treatment of AISI 4140 steel?

I need to achieve maximum impact energy and hardness at the same time.Any experiment or reliable article??

08 September 2017 9,874 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View