Why second phase particles cluster during cold work?

02 February 2018 0 2K Report

In the attached picture, rolling direction is from bottom to the top(vertical).

Badges
Science topic

More Hossein Ahmadi's questions See All

Is there a process for changing crystalline silicon nanostructures or nanoparticles to amorpous silicon which is going to be used in Li ion batteries?

Amorphous silicon has lower volumetric change than crystalline silicon during first cycles of charge and discharge. How can we prepare amorpous silicon from nanostructured crystalline silicon? Is...

10 November 2019 2,569 4 View

How to clean copper surface before coating process?

What are suitable reagents for removing oxide layer and grease or organic impurities from copper surface before the coating process?

07 August 2019 3,061 4 View

How to leach Fe impurities out of Silicon Suspension?

High energy ball milling used to prepare silicon micro and nano particles. I used magnetic separation to remove iron. But there is a small amount of iron left in the suspension. How can I remove...

06 July 2019 4,438 2 View

What are suitable reagents for color eching of AISI 304 stainless steel?

Any reagent for revealing microstructure, electroetching, chemical etchin, or other methods. I need the colorful microstructure image. I only need the artistic aspect of images!

06 July 2019 6,317 3 View

How to calculate density of a coating layer?

It's a coating with few micrometers in thickness. There are equations for thickness prediction. But for using them, I need to know the coating density. I'm using spray coating method. The...

06 July 2019 7,006 4 View

What are flow lines?

Does anyone knows a reference book that describes this phenomena? Are flow lines and shear bands the same or they're different from each other? why flow lines appear in micro structure? (Attached...

01 February 2018 3,291 0 View

Can grain structure be revealed using SEM?

can we see the grains and grain boundaries without using any etching procedure by SEM?

11 December 2017 8,141 2 View

What is the main reason for edge cracking of aluminum alloys during cold rolling?

sheet edge geometry change, workability limitation or something else?? Does anyone have studied about that?

09 October 2017 4,727 3 View

Can Quench and Partitioning heat treatmnet(Q/P) improve the impact energy of AISI 4140 steel?

08 September 2017 3,583 0 View

Does anyone know the best temperature for quench and best temperature for partitioning in Quench and Partitioning heat treatment of AISI 4140 steel?

I need to achieve maximum impact energy and hardness at the same time.Any experiment or reliable article??

08 September 2017 9,874 2 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Who of all the Global Scientific community will help me Prof. Dr. Yoshida make way for TPEOM, MEC ~EMC to return the atmospheric gases to the norma ?

TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...

03 August 2024 2,484 1 View

How to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field in Techplot?

Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You

02 August 2024 3,615 1 View

Does the delta function actually make sense to use on point particles?

The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.

31 July 2024 10,109 3 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why is trifluoroacetic acid (TFA) used in c-18 column?

I would like to know the role of the TFA (trifluoroacetic acid) used on reverse phase chromatography c-18 column. It's is often used with a concentration of 0.1% on the mobile phase.

23 July 2024 8,075 3 View

What are the modern methods for detecting nanoparticles?

Some of the techniques I am familiar with are standard. I would like to know which of the two methods under study is preferable, as well as the cost and list of particles and devices needed in...

22 July 2024 1,921 3 View

What are the moving particles in the organotypic slice culture?

Hi everyone, I experienced some moving particles in my mouse hippocampal slices. The media looks clear. Any idea what these moving particles might be? Thanks you!

22 July 2024 3,734 0 View