What are flow lines?

Hossein Ahmadi @Hossein_Ahmadi27

02 February 2018 0 3K Report

Does anyone knows a reference book that describes this phenomena?

Are flow lines and shear bands the same or they're different from each other?

why flow lines appear in micro structure?

(Attached image is microstructure of cold rolled and annealed aluminum alloy.)

Badges
Science topic

More Hossein Ahmadi's questions See All

Is there a process for changing crystalline silicon nanostructures or nanoparticles to amorpous silicon which is going to be used in Li ion batteries?

Amorphous silicon has lower volumetric change than crystalline silicon during first cycles of charge and discharge. How can we prepare amorpous silicon from nanostructured crystalline silicon? Is...

10 November 2019 2,401 4 View

How to clean copper surface before coating process?

What are suitable reagents for removing oxide layer and grease or organic impurities from copper surface before the coating process?

07 August 2019 2,913 4 View

How to leach Fe impurities out of Silicon Suspension?

High energy ball milling used to prepare silicon micro and nano particles. I used magnetic separation to remove iron. But there is a small amount of iron left in the suspension. How can I remove...

06 July 2019 4,269 2 View

How to calculate density of a coating layer?

It's a coating with few micrometers in thickness. There are equations for thickness prediction. But for using them, I need to know the coating density. I'm using spray coating method. The...

06 July 2019 6,846 4 View

What are suitable reagents for color eching of AISI 304 stainless steel?

Any reagent for revealing microstructure, electroetching, chemical etchin, or other methods. I need the colorful microstructure image. I only need the artistic aspect of images!

06 July 2019 6,161 3 View

Why second phase particles cluster during cold work?

In the attached picture, rolling direction is from bottom to the top(vertical).

01 February 2018 1,905 0 View

Can grain structure be revealed using SEM?

can we see the grains and grain boundaries without using any etching procedure by SEM?

11 December 2017 7,982 2 View

What is the main reason for edge cracking of aluminum alloys during cold rolling?

sheet edge geometry change, workability limitation or something else?? Does anyone have studied about that?

09 October 2017 4,589 3 View

Can Quench and Partitioning heat treatmnet(Q/P) improve the impact energy of AISI 4140 steel?

08 September 2017 3,443 0 View

Does anyone know the best temperature for quench and best temperature for partitioning in Quench and Partitioning heat treatment of AISI 4140 steel?

I need to achieve maximum impact energy and hardness at the same time.Any experiment or reliable article??

08 September 2017 9,764 2 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What kind of intervention will be relevant to increase motivation among young sport trainees?

Any suggestion on what book to read is also welcome.

03 March 2021 1,646 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View