Does ANSYS FLUENT couple with ADAMS for doing co-simulation ?

More Sina Salahshour's questions See All

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Can tannins that are dissolved in water interact with silicone oil?

Hello everyone, Does anybody know if phenolic plant extracts such as tannins dissolved in water can interact with silicone oil? (although silicone oil and water are immiscible).

03 February 2021 5,656 2 View

Aeration requirement in sludge buffer tank?

Hi, Normally the thickened sludge is kept in 'buffer tanks' before further dewatering. The buffer tanks should be aerated to avoid septic/anaerobic conditions. I am wondering how the air...

10 September 2020 395 3 View

How to define CCCV protocol by applied current and rest time?

Hello, I'm using COMSOL to model batteries (not the battery module) and I need to define the applied current as: charge (CCCV) + rest + discharge (CCCV) + rest I'm wondering if it is possible to...

19 August 2020 9,359 2 View

No title

I am trying to dehydroxylate glass powder. The powder is a mix of different types of glasses. Thus there are absolutely considerable amounts of hydroxyl units in the microstructure. I've checked...

10 October 2019 4,598 4 View

Is there any way to detect heavy metal conatminated areas using remote sensing? If so what data do you suggest to use?

Hello everyone. I am working on sustainable infrastructures and my goal is to select the most optimum site for infrastructures in my area of interest to gain maximum sustainability. To achieve my...

03 August 2019 1,081 8 View

The function of salt bridge in electrochemistry?

Hi We use a salt bridge in a Galvanic cell to maintain electron neutrality by transferring anions to the anode side and cations to the cathode side. The question is that why the existing SO4(2-)...

31 July 2019 4,224 7 View

What is the best approach to evaluate the hot corrosion resistance of the aluminide coatings?

What method do you propose to accurately assess the hot corrosion resistance of a NiAl coating applied on a nickel-based superalloy?

25 July 2019 7,188 3 View

Supporting researches on internal combustion engines despite the development of alternative vehicles. Is it necessary or not?

As alternative vehicles are rapidly expanding, it seems that some research institutes have decided to withdraw their supports from researches on internal combustion engines. Do you think this is...

04 May 2019 2,822 18 View

Reference exchange current density in Tafel equation for modeling of ORR in an alkaline fuel cell?

Hello, I'm going to model the cathode side (Pt/C) of an alkaline fuel cell. To use Tafel equation for obtaining Oxygen reduction reaction kinetic, I need to know the exchange current density...

28 April 2019 8,400 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Ahmed Al-Manea

Dear Sina Salahshour

Please give more details about your question. Is it 2D or 3D simulations?

Best regards

Sina Salahshour

Dear Ahmed Al-Manea

Drive mechanism is 3D in ADAMS and Flow part is 2D simulation in ANSYS FLUENT.

Amir Sabernaeemi

This paper may be useful:

Article A fully coupled analysis of unsteady aerodynamics impact on ...

Best,

Dear Amir Sabernaeemi ,

Thank you for your help

Best Regards

Marta Alonso

Hi @Sina,

Have you solve it? It is an interesting question.

I see in Adams web this option,

https://www.mscsoftware.com/product/co-simulation but using scFlow not Ansys Fluent.