Do Min6 cell lines adhere to glass slides?

More Shreyasi Asthana's questions See All

How to culture MIN6 cells?

Hello everyone!! I am trying to grow MIN6 cells, but I am unable to. The growth rate is too slow. I can hardly see 5-6 cells in the plate. Also the morphology of the cells is highly irregular. I...

07 August 2018 7,422 3 View

How to write a thesis title?

Can a thesis title be a question?

08 September 2017 7,161 2 View

Can anyone suggest me a protocol for analysis of ROS in aqeous solutions?

Hi I want to measure ROS in a aqueous solution containing a protein and ROS generating agents in buffered solutions. Is there a protocol for the same/ and is it ok to use DCFH-DA for this? Please...

31 December 2016 1,528 0 View

What are the criteria while using a protease inhibitor?

How should I choose an effective protease inhibitor which can can be used for the purification of a range of proteins to be purified by Q-sepharose or Ni-NTA or SP-sepharose?

06 July 2016 5,200 5 View

What is the optimal staining procedure for SDS-PAGE?

I have a protein to be expressed with an apparent MW of 18.4 Kda.For that I used 13% resolving gel.I use an unstained protein ladder.After the run was over, I stained the gel with commasie.The...

06 July 2016 8,133 5 View

How long a stock solution of amyloid proteins is stable in DMSO?

I have stored a stock solution of an amyloid protein in DMSO for a long time. How long it will be stable without aggregating or forming amyloids, so that I can use it for further studies/experiments.

05 June 2016 7,601 5 View

What should be the optimum protein load (volume and concentration) when purifying a protein by sephadex G 100 , Column chromatography?

What should be the optimum protein load (volume and concentration) when purifying a protein by sephadex G 100 , Column chromatography Any suggestions would be highly appreciated :)

31 December 2015 7,451 3 View

How would I do MM-PBSA analysis after MD simulations in GROMACS?

how would I do MM-PBSA analysis after MD simulations in GROMACS Is there a tool or software for analysing the MM-PBSA of protein ligand complexes

31 December 2015 7,038 3 View

What is microfluidic protein sizing?

Can anyone explain me what is the meaning and principle of microfluidic protein sizing

11 December 2015 4,706 4 View

How might I calculate Guanidinium concentration in molecular dynamics simulation of proteins?

Hi everyone!! While performing the MD simulations on proteins and studying their unfolding by Guanidium, How should one determine the guanidium concentration with regard to the number of molecules...

06 July 2015 4,535 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

The Curse of Evolution and Complexity?

Brain and body mass together are positively correlated with lifespan (Hofman 1993). The duration of neural development is one of the best predictors of brain size, and conception is the best...

05 August 2024 6,247 3 View

Cássio Prinholato da Silva

Do this cells need to grow necessarily in glass slides? Can't you grow in normal flask and after put in slides?

Steingrimur Stefansson

Hi Shreyasi, ATCC has this info on Min6.

https://www.atcc.org/Products/All/CRL-11506.aspx#culturemethod

Md Babu Mia

Hello Shreyasi Asthana ,

Kindly follow the links and papers. I hope, they will be helpful.

Best regards,

Babu

https://www.atcc.org/Products/All/CRL-11506.aspx#documentation