I am interested in establishing average readings of radioactivity for slags derived from metal smelting and more specifically steel production. Does anyone have any data or can direct me to where I might find this?
There are many references available. Try an internet search for "iron slag radioactivity"
Dear Jana,
Joseph was just a bit quicker tahn me :).
Indeed, there is quite a lot of published data available online.
Just as a taster you may take a look here:
Regards,
Pawel
https://www.google.co.uk/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwjAr4GJ3bPLAhVDXhQKHamHDSsQFgggMAA&url=http%3A%2F%2Fwww.nipne.ro%2Frjp%2F2011_56_7-8%2F1011_1018.pdf&usg=AFQjCNHgn1iq11bpRdbqAlutF-JhhXAr6A
Many thanks for this, overlooking the obvious!
Jana
My apologies, did I ever send you this? If no, do you still require this?
Best wishes
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I isolated microbial DNA from marine water samples taken at various sites using the Qiagen Power Water DNA Isolation Kit, including a modified enzymatic lysis step. I encountered a situation where...
24 July 2024 9,688 0 View
1. Nutritional contribution of the edible coating 2. Self life of the vegetable to be coated with the edible coating. 3. Toxicity development after preserving the vegetable with the edible coating.
11 June 2024 1,740 3 View
I am using 20 mg of WO3, 800 mg of Sulphur, 925 oc growth temp, 280 oc S temp, and a 20 sccm gas flow rate.
05 May 2024 8,665 2 View
I have questions regarding the safe use of cell phones in animal research facilities. While I acknowledge the hygienic risk, we often spend a lot of time inside our barrier SPF facility and we...
14 April 2024 3,486 0 View
Ladies and Gentleman, My name is Jana Maric, and I am a tourism management student at the university of applied sciences in Germany currently researching for my bachelor´s thesis in the field of...
08 April 2024 4,449 0 View
Please do it by hand, if not possible just do by some analytic engine.
26 March 2024 2,028 0 View
I deposited Ga2O3 thin film on fused quartz substrate at 500oc in Ar ambient by RF sputtering and then annealed at 900oc (very slow heating and very slow cooling i.e 1oc/min) in air ambient for 1...
11 February 2024 3,417 4 View
ANSYS multilinear material model does not support plastic strain vs stress data with a negative slope. Moreover, it assumes perfectly plastic (horizontal) behaviour from the end data point. How...
01 February 2024 9,950 0 View
INDIAN JOURNAL OF NATURAL SCIENCES ISSN: 0976-0997 ( Print, Bimonthly ) Multidisciplinary Sciences Web of Science Indexes: Zoological Record is this journal UGC care list II category?
25 December 2023 4,017 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?
31 July 2024 5,824 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
Dear all: I am modifying Bismuth Tungstate with Hematite (Fe2O3), so I would like to know about how much Iron(+3) can form a solid solution in a Bismuth Oxide matrix. Best wishes Marco
29 July 2024 2,163 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
We assume that there is a physico-statistical meaning to the constant π other than circular geometry, but the iron guardians of the Schrödinger equation deny this. The iron guardians of the...
22 July 2024 4,285 9 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View