Can we use Eddy Simulation to simulate flow separation in Reentry Capsule Afterbody flows?

01 January 2018 0 5K Report

At Hypersonic speed, can i use eddy to capture the flow separation and reattachment in the after body flow of a re-entry capsule

Badges
Science topic

More Manigandan Sekar's questions See All

In fluent heat flux analysis results are not converging ?

I had solved the heat flux analysis of the multi-domain problem in fluent. Even after the 20000 iterations also the solution is not converging. As the iterations increase the results are diverging...

10 November 2019 4,154 3 View

How to draft a review paper effectively in short span of time for high impact journals?

Writing a review paper required a lot of effort. Any tactics is there to complete it in short span of time. Especially for Elsevier or reputed journals with high Impact factor.

06 July 2019 2,461 3 View

Do addition of nanopartilces in soil increases the Plant yield ?

Can any one explain me that addition of nanoparticles enhances the growth of plant and produces more yield. If so, can anyone list me the nanoparticles i can use Plant is Tomato and Aubergines

05 June 2019 424 4 View

Second PhD in a “neighboring” discipline?

I came across few having 3 PhD in different fields. Am very confused about this ? Thanks in advance

02 March 2019 7,754 2 View

Is addition and removal of Co-author during submission of revised article is acceptable @Elsevier ?

I like to know the removal, addition and shuffling of co-authors is against moral and ethics in Elsevier Journals. Is it necessary to contact a editor to make such changes

01 February 2019 1,359 15 View

Differences between research papers and technical note of journal?

Can i write an technical note below 1000 words. If not what is the idle limit for them. Is there any mandatory rules

31 December 2018 9,412 1 View

Best way to access recent Engineering Books in online ?

I need to access the book : Energy Efficiency in Air Transportation Published by elsevier. I tried many options but no use. Since i can't afford to buy this, is there any way to access the ebooks

31 December 2018 4,391 4 View

How to solve Blast in FEA ?

What are the boundary conditions are required for blast loading. Share the tutorials if possible.

31 December 2018 1,425 0 View

What is the difference between review track and non review track in Elsevier conference ?

In Elsevier conference there are two options for paper submission Review track and non review track. What is the meaning for that. Will they publish both articles in supporting journal

07 August 2018 4,072 0 View

How to approach Faculty Exchange Program to the foreign Universities ?

Hi Am looking for an Faculty exchange programme vacancy in foreign universities to improve my career in technical fashion. I don't know how to start them. Can anyone guide me

07 August 2018 8,874 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to wash capsule filters (Membrane: polyethersulfone; pore size0.2u/0.45u) after filtration. can I wash by NaOH? if yes, what will be the molarity?

11 July 2024 8,969 1 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View