How to use the modelling equation of ANN for Genetic algorithm in optimization through ANN-GA hybrid method in matlab?

I want to use ANN-GA hybrid method for optimization. I know the use of ANN toolbox in matlab. but dont know where i can find the modelling equation of ANN so that i can use that for GA in matlab...

17 June 2020 6,518 5 View

Luenbeger observer

25 July 2017 8,002 5 View

Analysis help for benthic density/presence on sediment type in R

I collected benthic samples from 12 stations (3 samples per station across 4 locations) across mudflats from one estuary, in autumn & the following spring, totalling 72 samples. In addition, I...

10 July 2017 9,464 2 View

How do I calibrate a photo transistor with a solar cell based accurate irradiance sensor?

I want to build a low cost (not very accurate but with allowable margin of errors) solar irradiance sensor for my weather station using a photo transistor, but I am looking for the method of...

31 May 2017 530 3 View

What would you recommend for a simulation software to build a water based solar photovoltaic cooling system with all major components specifications?

What would you recommend for a simulation software to build a water based solar photovoltaic cooling system model with all major components specified with certain dimensions and capacities? The...

20 May 2017 5,643 2 View

How to measure all weather parameters at regular intervals with a simple unit or a group of instruments apart from using a compact weather station?

With weather parameters like solar irradiance, ambient temperature, relative humidity in air, wind speed and its direction, how could they be measured accurately and reliably in periodic intervals...

14 May 2017 9,377 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View