Can anyone explain me how to model RC beam in ansys workbench(rebars as line bodies and concrete as solid body)?

07 August 2020 1 8K Report

I modeled rebars as line bodies but when i insert link180 commands then it is not working.

. Cross mark will come in ansys mechanical.and not getting results. please show me as i am having really hard time in this.

Marco Gaetani d'Aragona

Hi,

it is difficoult to understand which is the problem you are facing and why Link180 is not working in you model.

If you are new to model reinforced concrete elements in ANSYS, I suggest to follow this video https://www.youtube.com/watch?v=h2BApwflt3E&t=417s . It explains very well how to model concrete with solid65 and rebars with link180 with an example. Maybe, by comparison, you can find which is the problem with your model.

Regards,

MGdA

Badges
Science topic

More Shreyas Alagundi's questions See All

Standardization of Overlap PCR or 2-Step PCR and its Yield?

Hi fellow researchers... I am trying to construct an Overlap PCR product in order to ligate it but am having difficulties in standardizing the protocol. I am able to perform the individual PCR and...

21 November 2023 8,460 5 View

Should I proceed if I accidently over incubated the sample after adding trizol?

I wanted to perform RNA extraction of U937 cells (Human Myeloid Lymphoma) by TRIZOL method, after adding TRIZOL to the sample I had kept it for incubation at room temp. and since I was not able to...

17 February 2023 7,049 1 View

Looking for a suitable thermal camera. Suggestions?

Hi, I am looking for suggestions for easy-to-handle thermal cameras. The camera should be capable of capturing thermal as well as RGB images of the subject. Also, the user should be able to...

22 September 2022 5,747 1 View

How to connect mesh between two 2D-geometry In ANSYS APDL using GUI?

I modeled 2 geometry with different materials in ANSYS APDL. how to connect mesh between them? I attached figure for better understanding. Figure A- My model.. Figure B - from research paper- (I...

26 July 2021 3,168 3 View

Problem while Implementing Wet Heat Exchanger Algorithm?

I was reading this research paper titled ' A Fully Wet and Fully Dry Tiny Circular Fin Method for Heat and Mass Transfer Characteristics for Plain Fin-and-Tube Heat Exchangers Under Dehumidifying...

03 March 2021 4,882 4 View

What are the optimum print parameters for Alginate-Gelatin Biopritning?

Can anyone share their experience of Bioprinting Alginate-Gelatin Bioink. Specifically, what temperature and pneumatic pressure are optimum for this combination to achieve a good resolution while...

26 November 2020 6,971 3 View

How to dissolve rotenone in Drosophila melanogaster food?

I wish to make a drosophila feeding medium with rotenone final concentration of 500uM. I came to know the way it is dissolved and the solvents involved, but am not clear with the full protocol....

13 October 2020 6,808 2 View

How to get predicted output values from Trained neural network?

I trained artificial neural network with 11 inputs and one output. There are total 74 data. I need to compare the predicted values with values calculated from equations of design codes. So can...

08 October 2020 9,123 3 View

How to calculate joint shear strength of RC Beam column joint form experimental data?

Can anyone explain me how to calculate shear strength of RC Beam column joints form experimental data? I have a experimental research paper from which I need to take out the joint shear strength...

19 September 2020 5,526 0 View

How can I design a network with 100s/1000s of nodes in NetSim?

I have tried doing this manually by modifying the configuration XML file. However, this is daunting since we need to hand-edit many of the variables such as IP addresses, MAC addresses, etc. which...

06 May 2020 8,347 6 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

Is it appropriate to use ARDL(autoregressive distributed lag model) with environmental Kuznets curve?

The underlying idea behind the environmental Kuznets curve is that GDP per capita initially increases environmental degradation but later reduces the environmental degradation as the result of the...

28 June 2024 949 0 View

Convergence problems using opensees and specifically openseespy, what algorithm and system should i use to avoid convergence problems ?

hi im performing IDA for a 30 story consisting of bearing wall system of special shear walls for gravity and lateral resisting system , i usually face convergence problems with that , the walls...

27 June 2024 9,492 0 View