What are suitable step to reverse motion of drill bit during dental implant in abaqus ?

Hello every one. I am working on modelling dental implant and need some guidelines. I have completed the initial step for implant which is to create cavity inside a jaw. For this i have used 4 mm...

09 October 2018 7,636 4 View

To analyze the heat transfer in cement kiln which software is best ABAQUS orANSYS ?

Hello everyone. I want to simulate heat transfer in cement Kiln and to analyze different modes of heat transfer including convection , conduction and radiation. I know ABAQUS is capable of...

08 September 2018 344 3 View

To simulate heat transfer in cement Kiln which ansys module would be most compatible?

Hello every one i want to simulate the different modes of heat transfer through cement Kiln. Conductive heat transfer from clinker to inside wall of cement kiln .Convective heat transfer to...

08 September 2018 6,354 3 View

Can anyone tell me issues related to solar-wind-diesel Hybrid power system ?

Hello every one i am working on underlining issues related to solar wind diesel hybrid power system .if anyone have data related to this .please do share it with me ?

11 December 2017 9,311 13 View

To model fatigue which option should be best Fe safe or ABAQUS?

i want to model fatigue for buried pipelines.Please tell me which software should be best for modelling

07 August 2017 1,554 4 View

To model low cycle fatigue for buried Pipeline which additional properties should be defined apart from elastic ,plastic and density ?

Hello every one .Hope you will be fine i want to model low cycle fatigue in ABAQUS for buried pipeline .Please guide to model during modelling in material section which additional properties...

06 July 2017 1,736 3 View

How to apply incremental load in abaqus with load maintained for 2 minutes at each increment to monitor structure?

Hy every one i want to load the wall incrementally with rate of 0.4 kN/s. i want the load to be maintained for 2 minutes at each increment to monitor the doformation of the structure .[lease guide...

05 June 2017 6,097 7 View

How to Define amplitude curve for internal pressure of pipeline ?

How to define the amplitude curve for the internal pressure of pipelines in abaqus while using the dynamic explicit step? is it be linear curve or constant curve ?

10 November 2016 9,462 0 View

What is difference between gravity and Body force in abaqus ?

i am trying to model the stress variation in underground pipeline under traffic loading .i am trying to define the self weight of body so when i used the body force the result is different and...

01 January 1970 4,218 3 View

Can Change in thickness of X70 steel pipe has an effect on its stress strain curve?

01 January 1970 9,655 3 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View