Arsalan Ahmad

15 Questions 11 Answers 0 Followers

Questions related from Arsalan Ahmad

What are suitable step to reverse motion of drill bit during dental implant in abaqus ?

Hello every one. I am working on modelling dental implant and need some guidelines. I have completed the initial step for implant which is to create cavity inside a jaw. For this i have used 4 mm...

10 October 2018 7,716 4 View

To simulate heat transfer in cement Kiln which ansys module would be most compatible?

Hello every one i want to simulate the different modes of heat transfer through cement Kiln. Conductive heat transfer from clinker to inside wall of cement kiln .Convective heat transfer to...

09 September 2018 6,460 3 View

To analyze the heat transfer in cement kiln which software is best ABAQUS orANSYS ?

Hello everyone. I want to simulate heat transfer in cement Kiln and to analyze different modes of heat transfer including convection , conduction and radiation. I know ABAQUS is capable of...

09 September 2018 453 3 View

Can anyone tell me issues related to solar-wind-diesel Hybrid power system ?

Hello every one i am working on underlining issues related to solar wind diesel hybrid power system .if anyone have data related to this .please do share it with me ?

12 December 2017 9,379 13 View

To model fatigue which option should be best Fe safe or ABAQUS?

i want to model fatigue for buried pipelines.Please tell me which software should be best for modelling

08 August 2017 1,634 4 View

To model low cycle fatigue for buried Pipeline which additional properties should be defined apart from elastic ,plastic and density ?

Hello every one .Hope you will be fine i want to model low cycle fatigue in ABAQUS for buried pipeline .Please guide to model during modelling in material section which additional properties...

07 July 2017 1,839 3 View

How to apply incremental load in abaqus with load maintained for 2 minutes at each increment to monitor structure?

Hy every one i want to load the wall incrementally with rate of 0.4 kN/s. i want the load to be maintained for 2 minutes at each increment to monitor the doformation of the structure .[lease guide...

06 June 2017 6,224 7 View

How to Define amplitude curve for internal pressure of pipeline ?

How to define the amplitude curve for the internal pressure of pipelines in abaqus while using the dynamic explicit step? is it be linear curve or constant curve ?

11 November 2016 9,509 0 View

How to to arrange Multiple ODB file under Combined ODB tool in Abaqus ?

Hy everyone.I am modelling Soil pipe interaction to check the Mechanical behavior of Pipeline.I have done multiple analysis under different Loading condition,Now i want to combine the multiple ODB...

01 January 1970 4,374 0 View

Can anybody help me to find Stress strain curve for API X70 pipeline ?

Hello everyone, I want to find the Data of full stress strain curve for standard X70 pipeline for FEA in Abaqus.Can anyone please help me regarding that

01 January 1970 2,615 0 View

S_N curve of steel is same for hollow and solid pipe ?

Hello everyone.I am working on Stress analysis on buried pipeline in scenario of dynamic loading. i am using API X70 pipeline.and i have calculated the Strenght .Now i want to calculate its...

01 January 1970 9,975 2 View

Can Change in thickness of X70 steel pipe has an effect on its stress strain curve?

I have read some where that thickness has no effect on the properties of steel i.e young modulus ,tensile strength etc. If it is true than why thickness has no effect on properties of steel ? I...

01 January 1970 9,710 3 View

Speed to wave deformation error of certain node in abaqus ?

Hello every one . i am modelling the soil pipe interaction in abaqus .I have done non linear analysis of pipeline crossing strike -slip fault and normal flexure load but when i off the non...

01 January 1970 8,230 1 View

When i increase seeds during mesh it give me speed to deformation error of node in abaqus .how to resolve it ?

Hy i am doing soil pipe interaction in abaqus .when i increase the size of the seeds during mesh beyond (0.75) Abaqus give me error that speed to wave deformation exceed at a certain node? when i...

01 January 1970 5,146 3 View

What is difference between gravity and Body force in abaqus ?

i am trying to model the stress variation in underground pipeline under traffic loading .i am trying to define the self weight of body so when i used the body force the result is different and...

01 January 1970 4,898 3 View