How to Define amplitude curve for internal pressure of pipeline ?

11 November 2016 0 10K Report

How to define the amplitude curve for the internal pressure of pipelines in abaqus while using the dynamic explicit step?

is it be linear curve or constant curve ?

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Arsalan Ahmad's questions See All

What are suitable step to reverse motion of drill bit during dental implant in abaqus ?

Hello every one. I am working on modelling dental implant and need some guidelines. I have completed the initial step for implant which is to create cavity inside a jaw. For this i have used 4 mm...

09 October 2018 7,757 4 View

To simulate heat transfer in cement Kiln which ansys module would be most compatible?

Hello every one i want to simulate the different modes of heat transfer through cement Kiln. Conductive heat transfer from clinker to inside wall of cement kiln .Convective heat transfer to...

08 September 2018 6,485 3 View

To analyze the heat transfer in cement kiln which software is best ABAQUS orANSYS ?

Hello everyone. I want to simulate heat transfer in cement Kiln and to analyze different modes of heat transfer including convection , conduction and radiation. I know ABAQUS is capable of...

08 September 2018 529 3 View

Can anyone tell me issues related to solar-wind-diesel Hybrid power system ?

Hello every one i am working on underlining issues related to solar wind diesel hybrid power system .if anyone have data related to this .please do share it with me ?

11 December 2017 9,411 13 View

To model fatigue which option should be best Fe safe or ABAQUS?

i want to model fatigue for buried pipelines.Please tell me which software should be best for modelling

07 August 2017 1,658 4 View

To model low cycle fatigue for buried Pipeline which additional properties should be defined apart from elastic ,plastic and density ?

Hello every one .Hope you will be fine i want to model low cycle fatigue in ABAQUS for buried pipeline .Please guide to model during modelling in material section which additional properties...

06 July 2017 1,861 3 View

How to apply incremental load in abaqus with load maintained for 2 minutes at each increment to monitor structure?

Hy every one i want to load the wall incrementally with rate of 0.4 kN/s. i want the load to be maintained for 2 minutes at each increment to monitor the doformation of the structure .[lease guide...

05 June 2017 6,252 7 View

Can Change in thickness of X70 steel pipe has an effect on its stress strain curve?

I have read some where that thickness has no effect on the properties of steel i.e young modulus ,tensile strength etc. If it is true than why thickness has no effect on properties of steel ? I...

01 January 1970 9,733 3 View

What is difference between gravity and Body force in abaqus ?

i am trying to model the stress variation in underground pipeline under traffic loading .i am trying to define the self weight of body so when i used the body force the result is different and...

01 January 1970 4,928 3 View

Speed to wave deformation error of certain node in abaqus ?

Hello every one . i am modelling the soil pipe interaction in abaqus .I have done non linear analysis of pipeline crossing strike -slip fault and normal flexure load but when i off the non...

01 January 1970 8,295 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View