What does Evaluation recommendation mean?

After submitting an article in a journal. I noticed following steps. 1) No editor assigned. 2) Evaluation recommendation. (After 6 days of manuscript submission) I didnt see any "under...

31 December 2017 9,057 14 View

How can I calculate an effective refractive index by using comsol?

I would like to calculate a sensitivity of a Si waveguide by using a formula= change in effective refractive index/change in sample index. I modeled my design in COMSOL in wave optics (ewfd) and...

09 October 2017 959 10 View

Fabry Perot filter?

I am designing a Fabry Perot filter with two alternating materials such as High refractive index material and air as a second material(low refractive index). Everything goes fine when I use the...

07 August 2017 8,793 4 View

Related to OPENFILTER software

05 June 2017 6,544 0 View

How can I remove Ti layer diffused with Cs?

During a Cs diffusion experiment, I deposited a Ti layer which acts as a hard mask on RbTiOPO4 substrate, but now properties of Ti have changed and Cs is also diffused into it. And it's not...

10 November 2013 8,018 6 View

How does one improve gold adhesion?

I want to improve the adhesion of gold on RTP (substrates), as I want to etch them finally to have electrodes. That Is why I was thinking to deposit Ti or Al layer between substrate and gold. I...

10 November 2013 5,982 15 View

Inductive heating in COMSOL

Hello all, I am simulating a 3D model of a copper coil carrying a current placed in a vacuum. Due to current flow, there is an inductive heating in the coil. To cool it, I am using a water...

01 January 1970 6,565 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View