Ansys Apdl Stress thermal Analysis ?

Mr. Mass @Mr_Mass

11 November 2015 1 3K Report

why there occurs large difference between thermal and stress thermal analysis results in ansys ?

Nirajkumar Mehta

I think you may be doing mistake in unit conversion for material properties or boundary conditions.

Badges
Science topic

More Mr. Mass's questions See All

When pressure is applied on piston crown, where will be the maxilum and minimum stresses ?

when pressure is applied on piston crown, where will be the maxilum and minimum stresses

04 May 2016 4,446 0 View

Simulation /wear Analysis of Turbine Blades ?

can anyone share some links/site having presentation / case study how to do Simulation /wear Analysis of Turbine Blades in ansys or any other simulation software . Please share some links / sites...

31 December 2015 5,602 3 View

While doing stress thermal analysis in the first part ( Thermal Analysis ) i am unable to have '' r.th '' file ?

Ansys Mechanical APDL FEA

10 November 2015 2,046 2 View

Ansys Apdl related to element type ?

My question consists of two parts 1-why different element types give different results even max stresses etc are also at different places ? 2-How we came to know that which element type is best...

10 November 2015 2,072 3 View

While Using Mechanical Apdl Ansys FEA and doing stress thermal analysis in the first part ( Thermal Analysis ) i am unable to have '' r.th '' file .?

Ansys FEA

10 November 2015 1,374 0 View

How we can do buckling analysis of truss on APDL Ansys ?

Truss buckling analysis

08 September 2015 1,975 1 View

Anyone user of Ansys APDL , Expert ?

how we can do buckling analysis of Trusses ?

08 September 2015 916 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View