When pressure is applied on piston crown, where will be the maxilum and minimum stresses ?

04 May 2016 4,420 0 View

Simulation /wear Analysis of Turbine Blades ?

31 December 2015 5,569 3 View

Ansys Apdl Stress thermal Analysis ?

why there occurs large difference between thermal and stress thermal analysis results in ansys ?

10 November 2015 2,566 1 View

Ansys Apdl related to element type ?

10 November 2015 2,042 3 View

While doing stress thermal analysis in the first part ( Thermal Analysis ) i am unable to have '' r.th '' file ?

Ansys Mechanical APDL FEA

10 November 2015 2,003 2 View

How we can do buckling analysis of truss on APDL Ansys ?

Truss buckling analysis

08 September 2015 1,921 1 View

Anyone user of Ansys APDL , Expert ?

how we can do buckling analysis of Trusses ?

08 September 2015 855 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View