When pressure is applied on piston crown, where will be the maxilum and minimum stresses ?

05 May 2016 0 4K Report

when pressure is applied on piston crown, where will be the maxilum and minimum stresses

Badges
Science topic

More Mr. Mass's questions See All

Simulation /wear Analysis of Turbine Blades ?

can anyone share some links/site having presentation / case study how to do Simulation /wear Analysis of Turbine Blades in ansys or any other simulation software . Please share some links / sites...

31 December 2015 5,602 3 View

Ansys Apdl Stress thermal Analysis ?

why there occurs large difference between thermal and stress thermal analysis results in ansys ?

10 November 2015 2,600 1 View

While doing stress thermal analysis in the first part ( Thermal Analysis ) i am unable to have '' r.th '' file ?

Ansys Mechanical APDL FEA

10 November 2015 2,046 2 View

Ansys Apdl related to element type ?

My question consists of two parts 1-why different element types give different results even max stresses etc are also at different places ? 2-How we came to know that which element type is best...

10 November 2015 2,072 3 View

While Using Mechanical Apdl Ansys FEA and doing stress thermal analysis in the first part ( Thermal Analysis ) i am unable to have '' r.th '' file .?

Ansys FEA

10 November 2015 1,374 0 View

How we can do buckling analysis of truss on APDL Ansys ?

Truss buckling analysis

08 September 2015 1,975 1 View

Anyone user of Ansys APDL , Expert ?

how we can do buckling analysis of Trusses ?

08 September 2015 916 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

Could GSH level be more in CCL4 rats than negative control rats?

i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....

26 July 2024 1,887 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

How do nutrient transporters and aquaporins interact under abiotic stress in plants?

"The Correlation between Nutrition and Transport Mechanism under Abiotic Stress in Plants: A Comprehensive Review" by Muhammad Saleem, Jianhua Zhang, Muhammad Qasim, Rashid Iqbal, and Li Song,...

23 July 2024 9,109 0 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How can alternative crops for augmenting farmers’ income in abiotic stress regions and impact of abiotic environmental stresses on crop quality?

13 July 2024 6,826 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View