A tough, malleable, iron-based alloy containing up to, but no more than, two percent carbon and often other metals. It is used in medicine and... | Contact experts in Steel to get answers
1,124 views 2,627 posts
Questions related to Steel
Good morning, all, I have created a lattice tower model with wire elements and assigned a truss profile and truss element mesh. Bottom 4 legs I make it fixed were as the top was free, applied load...
11 November 2022 547 4 View
If the fracture stress of one piece is higher than its yield stress, does it brittle fracture or ductile?
09 November 2022 1,240 1 View
1. What are the relevant test used for detecting the crack healing efficiency in self healing concrete?
07 November 2022 8,298 1 View
On the base of free energy and diffusion of carbon.
07 November 2022 7,709 0 View
anyone ?
07 November 2022 9,115 3 View
Hello all, I would like to export to an excel file all the data that has been recorded in my records modules in different excel files or in the same one, but different sheets per replication....
05 November 2022 5,306 2 View
The Background of the Question and a Suggested Approach Consider that, e.g., a tensile strength test has been performed with, say, three replicate specimens per specimen type on an inhomogeneous...
05 November 2022 5,952 2 View
Dear All I am trying to simulate the bond behavior between concrete beam and CFRP using ABAQUS. I tried different ways to do so, but no one works. I got the following errors as in the attached...
03 November 2022 9,349 1 View
I found difficult to quantify the heated affected zone visually from optical microscope. Are there any other technique (calculating surface roughness, color temperature or any other technique that...
02 November 2022 8,677 3 View
What information do we get from 2D optical graph of wear track related to tribology? Please check the attached file for 2D optical graph.
31 October 2022 8,247 2 View
I am having some project ideas. I like to convert into reserch proposal and apply for sponsored project. Please tell me the way to apply for sponsored project like DST, DRDO sponsorship.
27 October 2022 4,953 1 View
I am working on an implant meant for a mandible defect. When simulating the load case, the parts will always penetrate each other. There is a deformation scale factor of 90, so the penetration...
26 October 2022 4,517 5 View
Yield stress during uniaxial deformation strongly depends upon crystallographic texture in Mg, because it depends on easily operating basal slips. So varying the texture changes the average Schmid...
26 October 2022 6,487 3 View
I want to check the presence of cadmium ions in a complex by doing a Chemical analysis, kindly suggest a method.
26 October 2022 3,288 4 View
I conduct a microstructure experiment on AISI 1010 low carbon steel, and the result show that pearlite is more abundant than ferrite, whereas it should be the opposite.
26 October 2022 183 3 View
I would like to install the TSL OIM Analysis software but I cannot find the files at EDAX website. I have already a legal license, a USB dongle, but I want to reinstall it in a new computer but...
26 October 2022 5,302 3 View
I am trying to model fatigue crack propagation using XFEM in Abaqus and I observed that I could create three types of steps for this task: static-general, dynamic-implicit and direct-cyclic. What...
23 October 2022 7,685 4 View
This claim is from https://www.totalmateria.com/page.aspx?ID=CheckArticle&site=kts&NM=122 Higher temperature is supposed to make deformation easy , right? then why is this trend happening as per...
21 October 2022 253 0 View
I've few queries regarding bacterial and mammalian plasmids for expression of Gene of Interest. What plasmid elements/components that are differ between bacterial and mammalian Plasmids to express...
20 October 2022 3,641 1 View
Hi, I just installed Abaqus and run first job. When I open job monitor I see some data in "Message File" and "Data File" sections, but Errors, Warnings (despite there are warnings and errors...
19 October 2022 5,213 6 View
Where does one find the ranking of journals in terms of the quartiles (i.e. Q1, Q2, Q3 and Q4), and why is it important to consider the quartile rankings when selecting a journal to publish in?
19 October 2022 6,778 4 View
The general titration procedure was carried out based on Boehm’s method. A known mass of carbon. 1.5 g carbon was added to 50.00 mL of one of three reaction bases of 0.05 M concentration:...
19 October 2022 8,067 0 View
I would like to know ho the grain grows a technical detailed explanation with a visual
19 October 2022 6,905 8 View
Hi, I want to simulate the shape memory effect of nitinol and I'm having trouble figuring it out. Basically, I want to create a 3D CAD simulation of a part made out of nitinol and the effects of...
18 October 2022 9,597 2 View