A tough, malleable, iron-based alloy containing up to, but no more than, two percent carbon and often other metals. It is used in medicine and... | Contact experts in Steel to get answers
1,343 views 3,966 posts
Questions related to Steel
I am doing research on "RELATIONSHIP BETWEEN SUSTAINABILITY REPORTING AND CORPORATE FINANCIAL PERFORMANCE WITH THE MODERATING IMPACT OF CORPORATE GOVERNANCE: EVIDENCE FROM THE BANKING SECTOR OF...
15 October 2023 996 2 View
it is assumed that interpreting 4D seismic data shot over hydrocarbon reservoirs made of carbonates is more challenging than for clastic reservoirs. Then what could improve the value of 4D seismic...
14 October 2023 2,668 6 View
I send it in attachment file !
13 October 2023 4,988 1 View
I have tried dissolving the same at 1mg/ml in both water and DMSO but there was precipitate formation. I even tried heating and sonication but there was no effect as there were precipitates.
11 October 2023 2,097 1 View
Dear All, I am performing the frequency response analysis of the human body FE model using steady-state dynamics. I have given base acceleration in terms of amplitude and phase angle. The output...
09 October 2023 9,708 0 View
Hello Scholars, I am performing compositional analysis (using ICP-OES) of electroplated Nickel with mild steel (MS) as base substrate. I want to strip Nickel from MS without contaminating the...
06 October 2023 8,786 1 View
If yes, what is the ideal concentration of L-Arginine in DMEM?
05 October 2023 1,838 0 View
Hello, I'm conducting research on ZnO-based thermoelectric materials and have encountered several challenges. After sintering at 900°C for 1 hour, my samples shrink significantly (over 50%) and...
05 October 2023 8,263 3 View
Dear Researchers: I am wondering why we say the Climate is Changed. I think it doesn't make sense, because in science, the word "Change" is used to describe a situation when a phenomenon changes...
05 October 2023 6,080 12 View
Recently one of my Journal paper has been accepted in an Open Access renowned SCIE Journal of Mechanical Engineering. The paper was initially reviewed in a high impact factor subscription type...
04 October 2023 5,482 2 View
I'm encountering an issue while trying to read a file named 'Meta_31.txt' in R. Despite confirming the file's existence, verifying the file path, and trying various methods (e.g., read.table,...
04 October 2023 6,184 1 View
work article from answer any question in resaerchgate
04 October 2023 2,938 4 View
Hello everyone, I am trying to simulate a 2d nanoindentation experiment using abaqus in a force controlled manner. The indenter property is rigid and made a reference point on the same for the...
03 October 2023 7,520 0 View
Dear all, I am trying to model the contact between the BEAM elements in my model for collapse analysis. I start off with a simple analysis where I have modelled a beam hitting a column, as shown...
29 September 2023 567 4 View
How can constructed wetlands be used as wastewater treatment
28 September 2023 5,282 6 View
How to determine k,n, in the JMAK model through cct diagram and TT diagram ,is it necessary to do thermal simulation experiment?
26 September 2023 8,598 1 View
How does Earth's revolution affect the constellations that you see at night and what groups of constellations are found along the ecliptic ring?
26 September 2023 6,194 3 View
Temperature change rate should not exceed 150 °C/Hr for Alumina Crucible. Which material can withstand higher temperature change rate showing good thermal shock behavior.
26 September 2023 8,806 2 View
Dear All researchers I trying to make table like in the picture ( see in the attached). Somoene can help with stata comand to do it. Best regards
25 September 2023 1,134 0 View
Difference CO PULSE and CO2 PUSLE CHEMISORPTION for a catalyst characterization ? what are the information we will get from this experiments? Also the diffrence between the NH3 TPD and Co2 TPD?
24 September 2023 9,195 1 View
How is energy transferred from wind to the waves and how does radiation transfer thermal energy from the sun to the Earth?
24 September 2023 4,041 0 View
I can run Huang's CPFEM UMAT well on abaqus + inter parallar studio xe. But when I run the same model and UMAT on abaqus + oneapi, error occurs without any possible error messages. Since the...
23 September 2023 9,503 2 View
I have a 3D-printed part which contains paraffin wax and EVA and want to extract only the wax by solvent debinding.
22 September 2023 2,291 1 View
When validating the Doehlert Matrix Design, do we encounter the issue of the "ideal sample design space"? I mean, in designs like the Central Composite Design (CCD), validation is usually...
22 September 2023 9,718 1 View