Contact experts in Abaqus to get answers
17,858 views 5,564 posts
Questions related to Abaqus
In short, I am trying to obtain the well-known properties of water by using the T-history method for low-temperature PCM. I used ethylene glycol as the reference material and distilled water as...
03 October 2022 9,490 0 View
Hello Dears I had problemAbaqus in abaqus finding my analysis answer. it was just a simple static analysis but I faced this warning: The search database is sized too small. This message can be...
02 October 2022 5,470 0 View
I need maximum force in every drift in one Composite Shear Wall(CSPSW). I utilized dynamic Explicit and apply cyclic loading . I obtained hysteresis curve of my analysis. But how can I procure...
01 October 2022 7,581 1 View
I compared the three dimensional element stiffness matrix from self-developed code and abaqus. But significant difference can be found. In addition, my results agree well with those in a...
28 September 2022 5,175 2 View
I am running a model with ABAQUS/Standard, which is a axisymmetric model of stress-strain behavior(element type: CAX3). This model has three BCs: a) Displacement on the top edge; b) YSYMM on...
19 September 2022 9,221 0 View
The idea is to simulate a double glazed window exposed to solar radiation and see the maximum temperature in the glass. This temperature should be less than the maximum permissible temperature of...
19 September 2022 9,279 0 View
Hello, most of the non-linear buckling analysis problems use geometrical imperfections derived from the eigenmodes of the linear buckling analysis on a similar model. I would like to ask you how...
16 September 2022 2,729 0 View
I have a question regarding the Optistruct solver. In the case of a 1D joint approach, I would like to define the static and dynamic coefficients of friction at all joints of the mechanism. Would...
08 September 2022 3,173 0 View
Hello community, I'm trying to simulate cracks with cohesive elements (in Abaqus), but I would like to reproduce reality as much as possible. Therefore, I would first like to have elastic...
06 September 2022 9,951 2 View
Hi. I am a college student in South Korea. Questions arose while doing tensile and bending tests. Why is the tensile strength different in tensile and three-point bending tests? Thank you.
06 September 2022 1,599 2 View
I am validating this paper on ABAQUS and finding the peak overpressure value for blast loading on RC slab. The empirical equation in the picture and the ABAQUS IWCONWEP value is giving a very...
04 September 2022 8,725 0 View
I am trying to understand the hysteretic behavior of the material at the microscale. I came across a multi-yield surface model in plasticity where we can predict the nonlinear hysteretic behavior...
29 August 2022 8,816 0 View
Hi, I am trying to use python coding in an automated process of loading and analyzing small displacement FE problems using Abaqus software by mesh-to-mesh solution mapping technique. I have a...
25 August 2022 756 0 View
If you have any leads and reference material that would necessitate the acquisition of the information and protocol for the same I would be delighted.
23 August 2022 7,595 2 View
I'm performing simulation studies on bolted joints. I want to perform non-linear steady state dynamic analysis using ABAQUS. How to include damping effects caused by mating surfaces into the analysis?
19 August 2022 7,333 0 View
BLUF: I want to define an abaqus load step that I fully expect to cause plastic deformation in a model, but to abort it as soon as the plastic energy (output, ElPD) is measurably greater than...
19 August 2022 8,162 0 View
I have done a comparison by applying the hydrostatic pressure on the middle and top of the shell curve surface (Section Assignment: Shell offset = Middle or Top surface in Abaqus). In the case of...
18 August 2022 8,787 0 View
I tried to make Na[Al(OH4)] solution , using NaOH and Al2(SO4)3.18H2O as sources in 11:1 molar ratio , to have excess NaOH which prevents Al(OH)3 precipitation but still I see disperse...
15 August 2022 5,789 0 View
Hello, I plot a diagram (radiated power level) in ANSYS window by this command: ERPL, plas I need the data of the diagram. How can I access the data? I appreciate a step by step...
15 August 2022 6,495 1 View
Machine Design
11 August 2022 9,301 0 View
Hello. http : webbook.nist.gov. is a good online data bank for material properties. I have checked a few heat capacities of materials on that. The general form of formula is as follow: Cp° = A +...
09 August 2022 8,949 3 View
While performing a Monte Carlo simulation I get some "jumps" in the skewness and kurtosis as shown in the picture. How can you explain this odd behavior and non convergence of the beforementioned...
07 August 2022 5,875 2 View
Hello/Good day everyone! I want to make a FSP tool for work and need your worthy suggestions regarding the relation of FSP tool pin length and diameter? 1. If my tool pin length is 7 mm then what...
05 August 2022 9,433 0 View
I prepared 1:1 inclusion complex of flavonoid and HP-b-CD through freeze drying method . ( obtained AL type graph through phase solubility study conducted with different concentrations of CD) ....
04 August 2022 4,473 0 View