Contact experts in Abaqus to get answers
5,214 views 5,221 posts
Questions related to Abaqus
Hi I have downscaled RCMs using LarsWG. Now I want to create ensemble of these climate models. How should I proceed?
29 May 2022 2,390 0 View
Hi all, I am using Abaqus to simulate cylindrical turning. No matter how I set the mass scaling factor (16,100,256, etc.), the final kinetic energy is always greater than 5% of the internal...
24 May 2022 1,350 2 View
Hello, I'm trying to model a transient flow on a solid surface with a surface reaction. Initially, there is no fluid on the surface. Then, the fluid will be injected at a specific angle. When the...
24 May 2022 7,007 0 View
I am perfoming a simulation to determine the elastic/plastic behavior of a polymer material in abaqus.To simulate the plastic behavior of the material I am using a drukcer prager model. I have...
22 May 2022 7,878 1 View
I have a short column model and I want to analyse in Abaqus to see the damage
21 May 2022 4,705 2 View
Hi, I would like to create a set similar to the one below. Using the findAt method is time consuming because it would require to enter the coordinates of all the edges that I need. Instead,...
20 May 2022 9,379 5 View
I have been using Direct Cyclic Approach using XFEM method to find Fatigue Crack Growth, but I am not able to find da/dN vs Delta K from Abaqus. How we can find number of cycles taken to grow...
20 May 2022 3,798 3 View
hello guys. i do the sloshing analysis with CEL method using ABAQUS. we want to find out the effect of baffle in the tank. so we applied the displacement boundary condition at tank plate. and we...
19 May 2022 8,203 2 View
I want to continuously change the rigid tool orientation during the machining in Abaqus. what strategy can be used to accommodate tool orientation in Abaqus/Explicit? How can I provide both...
18 May 2022 5,625 3 View
I now have a 1D structure with materials with two Young's modulus, and I want to analyze its response to different frequencies. For example, the bandgap of the structure. I am wondering if Abaqus...
16 May 2022 328 3 View
The problem is that the ABAQUS has limit number of 10e7 (one billion) for number of time increments. Is any way to use more than one billion? I need it for fatigue analysis. Thank you.
14 May 2022 8,440 2 View
How to apply exponential cohesive law in abaqus using tabular data?
11 May 2022 9,070 1 View
The GE send me a comment on formatting the manuscript including in-text and bibliography as per JGOSS journal. So I'm looking for a latex template for a manuscript emerald insight / Journal of...
11 May 2022 9,288 0 View
I am trying to model rotational displacement using static procedure of Abaqus. I found an example of dynamic procedure but i couldn't found any for this problem.
10 May 2022 6,885 2 View
I tried to use Abaqus for external turning simulation, set the workpiece speed to 6.28/s, and set the analysis step time to 1. Theoretically, the workpiece should rotate one revolution, but the...
09 May 2022 7,699 8 View
Thank you for help.
09 May 2022 4,271 1 View
A flow curve is important for the accuracy of finite element simulation. However, the stress and strain gained by the uniaxial tensile test are insufficient to characterize the flow curve of sheet...
09 May 2022 5,817 2 View
How can we model UO2 densification in Abaqus?
07 May 2022 3,850 1 View
I am working on a model in ABAQUS, where it requests material orientation should be varied with time, as far as i know, the orientation in ABAQUS can only be spatially different when using...
07 May 2022 413 1 View
I am currently working on the project of single-point incremental forming by using Abaqus explicit analysis. I have successfully run the simulation and generated results. In my simulation magnet...
06 May 2022 7,237 2 View
I am trying to use the jupyter notebook as a way to change the script for an analysis and view the output?
06 May 2022 6,198 1 View
Hello DAMASK and ABAQUS users, I want to run dislocation density based crystal plasticity finite element analysis in ABAQUS using DAMASK CP codes. I am able to run the simulations on the small...
06 May 2022 5,413 4 View
I am trying to model a 3D End Notched Flexure test using ABAQUS. The end notched flexure specimen consists of two beams with a cohesive element interface and a pre-crack. The test uses a three...
04 May 2022 3,894 2 View
I simulated a push-out experiment Of a timber-concrete-combined- ceiling system In Abaqus. as an result I need a force-displacement curve. The calculation stopps after the failure. But I need to...
29 April 2022 2,294 2 View