I am scanning CV curves using 3M Na2SO4 electrolyte in Ag/AgCl, Pt mesh and Phos-COF as my positive electrodes, respectively. Every time it gives me straight line at 0. Why this happens?
How we can determine the proper value of current density that i should apply to this system? What is the general procedure to select suitable current density to that system which i mention above....
02 March 2019 9,668 2 View
How we can explain this ...
02 March 2019 7,429 3 View
I am using 3M KOH as electrolyte with Pt counter as counter and Ag/AgCl as reference electrode for my system.with increasing current density why potential is increases? Is this is unusual behavior...
01 February 2019 9,490 4 View
Is its a normal behavior? If not, then any reason, any comments, suggestions will be highly appreciated
31 December 2018 557 6 View
I am using the desired setup for CCD in my work. my question is, what does these value corresponds to how much current in ... A/g?
31 December 2018 5,160 3 View
The graph between number of cycles with respect to specific capacitance
31 December 2018 9,000 0 View
I want to use NCS/CNT as cathode and Carbon fiber paper (CFP) as anode for supercapacitor assembly and i want to widen the potential window. My question is; what is the criteria to take anode...
11 December 2018 7,797 0 View
NiCo2S4 with 6M KOH electrolyte with Ag/AgCl used as reference electrode
08 September 2018 2,531 4 View
I am using 6M KOH electrolyte and tested the behavior of Ni foam without pressure and with pressure. I observed that, with no pressure (without press Ni foam) the current is very high as compared...
03 April 2018 3,736 7 View
I need 7000 cycles but which one i run for numbers of cycles as i mentioned above Thank You
03 April 2018 9,400 1 View
I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...
02 March 2021 7,626 1 View
I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...
02 March 2021 5,829 1 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...
01 March 2021 2,207 3 View
I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...
27 February 2021 1,829 3 View
During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...
25 February 2021 7,994 3 View
Hi, I am trying to learn the theoretical modelling of silver nanoparticle using the Mie scattering theory. After that, I discovered a software named Mieplot developed by Philip Laven, where it...
25 February 2021 7,493 6 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View
What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.
22 February 2021 1,515 1 View
Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...
21 February 2021 8,132 1 View