Who has experience with Ansol Transmission 3D?

Franco Concli @Franco_Concli

04 April 2018 0 6K Report

Has someone experience on the computational performances of this software with respect to general purpose FEM software?

Franco

Badges
Science method

More Franco Concli's questions See All

Is possible to simulate wave propagation in solids with Code-Aster?

Is Code-Aster capable to simulate transient lamb wave propagation? Franco

31 December 2017 1,813 3 View

Best OpenSource FEM?

Dear all, which is the best open-source / free FEM software? I'm using Code-Aster and I'm pretty satisfied... but are there alternatives?

11 December 2017 3,161 0 View

Non-Newtonian modeling of fresh concrete: parameters?

Can anyone please give me some reference to find the non-Newtonian model parameters for simulating fresh concrete or mud... Regards Franco

10 November 2016 4,619 2 View

Best free FEM software?

Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco

07 August 2016 921 1 View

Available dynamic modeling softwares?

Which are the best available free dynamic analysis softwares for multi-body simulations? Regards Franco

01 February 2016 9,252 3 View

How can I calculate radial ball-bearing stiffness?

How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...

01 February 2016 7,228 4 View

Frequency response scilab?

Dear all, can someone give me some information about how to perform a frequency response analysis of a multi-dof system. Regards Franco

31 December 2015 1,168 1 View

Which is the best way to perform EHL simulations?

Dear all, which is the best way to perform EHL simulations? Is there some already developed free too alvailabe? Franco

07 August 2015 5,135 4 View

How should I set the sixDoFRigidBodyMotionCoeffs in OpenFOAM in order to have a proper mesh deformation?

Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...

10 November 2014 5,764 3 View

Someone interested in a FEM course with open-source software Code_Aster??

Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes

01 January 1970 3,676 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Has anyone looked into the stability of FEM methods on curved meshed?

Google scholar isn't giving me any results on this

27 July 2024 595 2 View

Cell optimization in 1D Nanotubes?

Dear All, I use Quantum Espresso. I want to optimize the structure of the carbon nanotube using the vc-relax. I got confused about how to fix cell_dofree here. For 3D, cell_dofree = 'all' or...

22 July 2024 5,708 0 View