Available dynamic modeling softwares?

More Franco Concli's questions See All

Who has experience with Ansol Transmission 3D?

Has someone experience on the computational performances of this software with respect to general purpose FEM software? Franco

03 April 2018 5,755 0 View

Is possible to simulate wave propagation in solids with Code-Aster?

Is Code-Aster capable to simulate transient lamb wave propagation? Franco

31 December 2017 1,813 3 View

Best OpenSource FEM?

Dear all, which is the best open-source / free FEM software? I'm using Code-Aster and I'm pretty satisfied... but are there alternatives?

11 December 2017 3,161 0 View

Non-Newtonian modeling of fresh concrete: parameters?

Can anyone please give me some reference to find the non-Newtonian model parameters for simulating fresh concrete or mud... Regards Franco

10 November 2016 4,619 2 View

Best free FEM software?

Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco

07 August 2016 921 1 View

How can I calculate radial ball-bearing stiffness?

How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...

01 February 2016 7,228 4 View

Frequency response scilab?

Dear all, can someone give me some information about how to perform a frequency response analysis of a multi-dof system. Regards Franco

31 December 2015 1,168 1 View

Which is the best way to perform EHL simulations?

Dear all, which is the best way to perform EHL simulations? Is there some already developed free too alvailabe? Franco

07 August 2015 5,135 4 View

How should I set the sixDoFRigidBodyMotionCoeffs in OpenFOAM in order to have a proper mesh deformation?

Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...

10 November 2014 5,764 3 View

Someone interested in a FEM course with open-source software Code_Aster??

Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes

01 January 1970 3,676 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View