Who has experience with Ansol Transmission 3D?

Has someone experience on the computational performances of this software with respect to general purpose FEM software? Franco

03 April 2018 5,527 0 View

Is possible to simulate wave propagation in solids with Code-Aster?

Is Code-Aster capable to simulate transient lamb wave propagation? Franco

31 December 2017 1,679 3 View

Best OpenSource FEM?

Dear all, which is the best open-source / free FEM software? I'm using Code-Aster and I'm pretty satisfied... but are there alternatives?

11 December 2017 3,012 0 View

Non-Newtonian modeling of fresh concrete: parameters?

Can anyone please give me some reference to find the non-Newtonian model parameters for simulating fresh concrete or mud... Regards Franco

10 November 2016 4,464 2 View

Best free FEM software?

Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco

07 August 2016 715 1 View

Available dynamic modeling softwares?

01 February 2016 9,095 3 View

How can I calculate radial ball-bearing stiffness?

How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...

01 February 2016 7,032 4 View

Frequency response scilab?

31 December 2015 966 1 View

How should I set the sixDoFRigidBodyMotionCoeffs in OpenFOAM in order to have a proper mesh deformation?

Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...

10 November 2014 5,527 3 View

Someone interested in a FEM course with open-source software Code_Aster??

Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes

01 January 1970 3,513 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View