Non-Newtonian modeling of fresh concrete: parameters?

More Franco Concli's questions See All

Who has experience with Ansol Transmission 3D?

Has someone experience on the computational performances of this software with respect to general purpose FEM software? Franco

03 April 2018 5,755 0 View

Is possible to simulate wave propagation in solids with Code-Aster?

Is Code-Aster capable to simulate transient lamb wave propagation? Franco

31 December 2017 1,813 3 View

Best OpenSource FEM?

Dear all, which is the best open-source / free FEM software? I'm using Code-Aster and I'm pretty satisfied... but are there alternatives?

11 December 2017 3,161 0 View

Best free FEM software?

Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco

07 August 2016 921 1 View

Available dynamic modeling softwares?

Which are the best available free dynamic analysis softwares for multi-body simulations? Regards Franco

01 February 2016 9,252 3 View

How can I calculate radial ball-bearing stiffness?

How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...

01 February 2016 7,228 4 View

Frequency response scilab?

Dear all, can someone give me some information about how to perform a frequency response analysis of a multi-dof system. Regards Franco

31 December 2015 1,168 1 View

Which is the best way to perform EHL simulations?

Dear all, which is the best way to perform EHL simulations? Is there some already developed free too alvailabe? Franco

07 August 2015 5,135 4 View

How should I set the sixDoFRigidBodyMotionCoeffs in OpenFOAM in order to have a proper mesh deformation?

Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...

10 November 2014 5,764 3 View

Someone interested in a FEM course with open-source software Code_Aster??

Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes

01 January 1970 3,676 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Zero pivot in Abaqus concrete 3D printing simulation using model change?

Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...

06 July 2024 2,130 0 View

What heavy aggregates are available for protective concrete in your country?

01 July 2024 1,625 3 View

Poured Earth Concrete ?

What are the benefits and advantages of concrete flooring when used in parking lot floors, and what are the technical requirements and general specifications that should be considered to ensure...

29 June 2024 2,171 5 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View

What can the authors say about the interface problem between the concrete core and the CFRP shells? What is the adhesion type like?

I submitted my journal and got some comments, I have answered and corrected all the comments from the reviewer but I don't understand how to answer this question. any expert researcher help me to...

20 June 2024 3,802 1 View

Asked a question in geopolmer concret ?

What are the realistic applications of self-compacting geopolymer concrete in the world? Are there names of projects implemented with this concrete around the world? Please mention the names and...

20 June 2024 6,040 2 View

Messaoud Saïdani

Hello Franco

There is a nice PhD dissertation that covers this topic I think. The link is:

http://www.qucosa.de/fileadmin/data/qucosa/documents/13175/PhD_Shyshko_qucosa.pdf

There is also:

http://www.rilem.org/docs/2014115208_star-222-scf_draft-version_full.pdf

Best wishes with the research

Devadoss Suresh Peter

It is of no practical use. Only statistical analysis is of practical use since the variations are too many