Who has experience with Ansol Transmission 3D?

Has someone experience on the computational performances of this software with respect to general purpose FEM software? Franco

03 April 2018 5,527 0 View

Is possible to simulate wave propagation in solids with Code-Aster?

Is Code-Aster capable to simulate transient lamb wave propagation? Franco

31 December 2017 1,679 3 View

Non-Newtonian modeling of fresh concrete: parameters?

Can anyone please give me some reference to find the non-Newtonian model parameters for simulating fresh concrete or mud... Regards Franco

10 November 2016 4,464 2 View

Best free FEM software?

Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco

07 August 2016 715 1 View

Available dynamic modeling softwares?

01 February 2016 9,095 3 View

How can I calculate radial ball-bearing stiffness?

How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...

01 February 2016 7,032 4 View

Frequency response scilab?

31 December 2015 966 1 View

Which is the best way to perform EHL simulations?

Dear all, which is the best way to perform EHL simulations? Is there some already developed free too alvailabe? Franco

07 August 2015 4,980 4 View

How should I set the sixDoFRigidBodyMotionCoeffs in OpenFOAM in order to have a proper mesh deformation?

Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...

10 November 2014 5,527 3 View

Someone interested in a FEM course with open-source software Code_Aster??

Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes

01 January 1970 3,513 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View