Is Code-Aster capable to simulate transient lamb wave propagation?
Franco
Hi Franco
Perhaps this paper is of use? The approach, I believe, can be made with any FE software. http://kth.diva-portal.org/smash/get/diva2:683355/FULLTEXT01.pdf
Sincerely
Claes
You can do dynamic simulations with Aster, linear or not (take a look for instance at DYNA_NON_LINE aka the non linear dynamics solver).
Could you provide an example? (.comm and mesh file)
Thanks
Has someone experience on the computational performances of this software with respect to general purpose FEM software? Franco
03 April 2018 5,527 0 View
Dear all, which is the best open-source / free FEM software? I'm using Code-Aster and I'm pretty satisfied... but are there alternatives?
11 December 2017 3,012 0 View
Can anyone please give me some reference to find the non-Newtonian model parameters for simulating fresh concrete or mud... Regards Franco
10 November 2016 4,464 2 View
Dear all, which are the most powerfull FEM free available softwares for structural simulation analysis? Best regards Franco
07 August 2016 715 1 View
01 February 2016 9,095 3 View
How can I calculate the radial stiffness of ball-bearing? I have found this formulae k=b*d+c where d: diameter b=1300 for ball bearing c=62500 for ball bearing A 6008 bearing has therefore a...
01 February 2016 7,032 4 View
31 December 2015 966 1 View
Dear all, which is the best way to perform EHL simulations? Is there some already developed free too alvailabe? Franco
07 August 2015 4,980 4 View
Dear all, I need help in setting up the dynamicMeshDict for pimpleDyMFoam using sixDoF. Actually I have 2 concentric cylinders (2d) representing a shaft and a hole (journal bearing). On the...
10 November 2014 5,527 3 View
Are interested in a course with Code_Aster? Unibz is organizing a 3-day course in October 2019. https://www.unibz.it/en/events/132491-engineering-simulations-with-open-source-codes
01 January 1970 3,513 4 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
There is confusion regarding the submillimeter-wave range. Many papers specify its range from 300GHz but some also consider its range from 100GHz. If I design an antenna on 122ghz what would I...
01 March 2021 516 7 View
I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...
28 February 2021 6,282 9 View
28 February 2021 5,433 3 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...
27 February 2021 5,969 1 View
I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...
27 February 2021 4,218 7 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View