Which surfactant is better Tween 20 or Tween 80 and why?

More Pinak Patnaik's questions See All

Is there a good way to find ZZ symmetric basis for 1D Quantum Lattice?

Hello, I am working with a Hamiltonian with ZZ conservation symmetry. From what I know, if a symmetry is known for a given Hamiltonian and we can find a basis for that symmetry, then we can,...

28 March 2024 3,570 0 View

The role of neurocognitive science in HR?

I want to know how organizations can study the behavior's of employees through neuro cognitive science and what role is played by Hr in gathering the desired answer from the minds of the employees.

18 December 2023 2,387 4 View

"How Transformational Leadership leads to better Organizational Performance With the mediating role of Talent Management in context to Indian Psu."?

I need the key variables and Latent variables which help Transformational leadership to achieve better organizational Performance with the mediating role of talent management.

11 December 2023 1,695 1 View

How to do Roughness calculation from wyko vision ascii file using MATLAB?

Hello everyone, I'm experiencing an issue regarding surface roughness calculation and I could use some help in troubleshooting. Here's what I've done so far: I measured surface roughness using an...

12 July 2023 8,005 2 View

How to make polycrystal files work in lammps?

I created a file af polycrystal diamond using atomsk and saved it using .lmp extension. When I run the file in lammps it is unable to read it but when I prepare a .lmp file for single crystal...

22 February 2023 2,034 3 View

If we are doing a solid solid diffsuion between two solids . How do we calculate the etching rate and other arehnius parameters?

Suppose I have solid 1 = poly crystal diamond solid 2 = Iron I put iron plate over diamond and anneal it at a temperature that facilitates diffusion. Carbon will diffuse into iron How will I...

31 December 2022 547 1 View

Any method to approximate grain orientation of polycrystal diamond over a large surface (1mm *1mm)) ??

For instance I need to know statistically in a area of 1mm * 1 mm how many 110 or 101 or 011 grains are present or grains closer to any one of these will be mapped under one these plane group. I...

02 August 2022 2,405 2 View

How do I stop my gel from getting solid?

Hello all I have been trying to prepare Co doped TiO2 nanoparticles through sol gel method. I have a issue where my gel usually forms after 24 hrs but it is dried and its not viscous anymore. Can...

24 March 2022 9,123 3 View

Is a binder absolutely needed in sol-gel spin coating method?

Hello all I am trying to prepare TiO2-Co doped nanoparticles thin films in order to study degradation of a dye. I will be using spin coating method to prepare the films. My question is if a...

10 March 2022 3,131 4 View

How to determine formula of Prussian blue derivative experimentally with least assumptions ?

I am trying to determine molecular formula of my Prussian blue analogue from experimental data. I have TGA data which gives me the amount of water and I have ICP data which gives me K/Fe . So...

22 February 2022 983 5 View

How to draw the five chelate rings of [Co(EDTA)]- on this picture?

Is this circle one of the rings?

03 August 2024 5,988 0 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

What exactly is it about biotechnology and medical research?

I'm very interested in biotechnology and medical research and I'd like to meet a professional here and talk about it together

28 July 2024 3,798 4 View

How does the Retention time effect the Biogas Production?

List down the various factors responsible and how does this effect the overall biogas production when it is related to Hydraulic retention time of the digester based on the feedstock?

27 July 2024 4,800 4 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Can any one let me know the PDE value for Tert-Butylamine in order to control in the API?

PDE value for Tert-Butylamine

24 July 2024 1,166 0 View

Do you know CUSABIO Biotechnology Scholarships for Students 2024?

I am pleased to announce the CUSABIO Biotechnology Scholarships for Students 2024! This scholarship aims to support outstanding students pursuing studies in the field of biotechnology. Here are...

22 July 2024 5,790 1 View

How are clinical and environmental yeast/fungal strains stored usually in mycology laboratories?

I understand a glycerol stock for long-term preservation would be ideal, but how are working cultures generally stored? Mainly concerning Candida spp. isolates. A few references mention that they...

22 July 2024 6,592 3 View

Biomerieux API Campy performance?

Hello, I have a somewhat weird question: has anyone had problems with campylobacter growing in the second half of the strip GLU through ERO? Have you managed to correct it? There is some...

19 July 2024 3,094 2 View

Xavier Turon

The obvious, non-ionic surfactants with different chain length resulting in different cmc values for example.

But "better" in terms of....which application?

Didier Fesquet

You might find some infos in the millipore booklet...

Pinak Patnaik

Xavier Turon Sir,

I am using the surfactant in electrodeposition of metals. I want to know which among the two can be a suitable surfactant that can be used in industry for obtaining superior deposit quality of metals?