Glycerol,sodium hypochloride,SEM,Sputtered coating,CPD
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
Now research fellow used it to prevent fungus in potato,may be potatoes gene effect.
02 August 2024 180 3 View
Please discuss someone told about fungus and allied others.
31 July 2024 3,372 3 View
We conducted an antibacterial study of a plant extract. Varying concentrations of crude extract were subjected to microbroth dilution assay. The result showed that only the lowest concentration of...
31 July 2024 8,666 3 View
Please note it
29 July 2024 4,920 3 View
https://www.cleanteqwater.com/resources/case-studies/gold-mine-australia/
29 July 2024 5,161 1 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
Why knockouts for same genes from two different gRNA are showing different result? I followed CRISPR-CAS9 gene editing technology.
25 July 2024 8,313 1 View
Cow dung manure is more powerful than artificial fertilizer.
19 July 2024 7,392 7 View
If the case of Irak is of December 2020 then i think I can suggest pl follow all the infection cause and death, already in our researchgate.
19 July 2024 3,356 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...
23 July 2024 1,649 1 View
I understand a glycerol stock for long-term preservation would be ideal, but how are working cultures generally stored? Mainly concerning Candida spp. isolates. A few references mention that they...
22 July 2024 6,592 3 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...
01 July 2024 2,686 2 View
I am fabricating the Hall bar (5 micron width and 35 micron length) of Ta(3nm)Co(4nm)Pt(5nm) using photolithoghaphy and sputtering. This Hall bar is connected by contact pads of Ti(10nm)/Au(60nm)...
29 June 2024 2,079 3 View
Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...
24 June 2024 1,605 0 View
Bonjour, j'ai une question si quelqu'un a une réponse. J'ai une colonne Uptisphere Strategy 100 Å Bonding HILIC-HIT avec une taille de particules de 3 µm et une longueur de 100 mm. Je n'arrive pas...
24 June 2024 7,201 1 View
We have observed many holes on the surface of TiO2. These holes have a diameter of approximately 1 µm and a depth of about 30 nm. The formation of these holes is mainly related to the...
20 June 2024 3,861 1 View
I conducted GIXRD measurements after performing O2 plasma treatment on a Cu surface. It was observed that the baseline is significantly high at low angles (10-30 degrees). What could this...
18 June 2024 2,996 3 View