I thought that Thiol (-SH) is positive charge, because it can bind to metal (eg. AuNPs) that has been coated by citric acid that would be negative.
Previously, I made Pb(NO3) stock in miliQ water and diluted into buffer. But I tried different way yesterday. I prepared 100 uM of Pb(NO3) in buffer 10 mM TA containing 50 mM NaCl, pH: 7.0-7.4 The...
01 February 2020 1,629 2 View
Yesterday I synthesized 13 nm colloidal gold nanoparticles using hotplate stirrer (T= 300 C, s= 600 rpm), the solution boiled for a long time (until bubles out). Even it had already ~ more than 1...
03 April 2019 653 6 View
Normally, I have fresh prepared TAE/TBE buffer. But sometimes I see one of my colleagues who re-use it max. 3 times, Is it corret or not? Does it have any effect to the result? Thanks
02 March 2019 814 3 View
I have DNA (disulfide modifier) has already become the Thiol due to adding TCEP. So I want to make it be disulfide again. Thanks
07 August 2018 466 0 View
I have 25 mM of Tris-acetate pH = 7.4 But, I need 25 mM of Tris-acetate pH = 8.2 for washing my DNA. I read a protocol, the adjuster should be using Acetate glacial. But, I have already adjusted...
07 August 2018 8,066 3 View
I need to block AuNPs surface (space between Thiol DNA - AunNPs) to prevent binding interaction with streptavidin.
07 August 2018 6,721 2 View
Yesterday I prepared 100 mM of MgCl in PBS 1X then sterilized it by autoclave. But my buffer was precipitated. How to prevent this matter? Thanks
07 August 2018 3,929 0 View
I read one paper (Hai-Bo Wang, 2013/DOI: 10.1039/c3nj00328k), he claim that there are approximately 50 strands of DNA probe for each AuNP. But, when I check a table from this paper (please check...
06 July 2018 1,391 1 View
I want to check the DNA strand displacement possibility of my DNA.
05 June 2018 645 0 View
I use that DNA marker in same concentration of gel (10%) and running at 80 V for 80 minutes (everything is the same).
04 May 2018 8,046 8 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Palmitic acid presence in aqueous fraction
05 August 2024 8,624 4 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
Hello, if you made a transwell assay where you incubate the cells with a nanoparticle-encapsulated drug and considering that in the oposite compartment you'll have both the free and encapsulte...
03 August 2024 2,730 1 View
I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?
02 August 2024 7,186 6 View