model isolated tanks in abaqus
I think wire part with T3D2 truss element is similar. i hope it helps
Dear mohammed
you can use T3D2 element in abaqus.i attached a picture, it will be help you.
best regards.
behzad
I need someone suggestions for running OpenSEES and performing analyses using python. Please help me regarding implementation of OpenSEES from python.
08 September 2017 10,092 1 View
A given receiver has received the signals in the graph. It is aimed to extract the red signal. Is there an idea for that?
07 August 2017 9,557 1 View
In our study using a herbal extract in a large dose, we found that the nucleus engulfs the mitochondria in cardiac myocyte of rat in a way similar to phagocytosis. All heart injury markers and...
11 December 2016 7,771 7 View
Since the Euler grid is only used in dynamic explicit analysis, the first gravity load step is also solved by this method. The gravity load is applied to the model very slowly during the first...
05 June 2016 3,350 0 View
i mean maximum result through all values during step time, is there any script in abaqus can do this ??
05 June 2016 1,437 0 View
in nonlinear analysis , what i do before is define only elastic and plastic stress vs strain and define fracture point value , yesterday i read this paper and found that there is also parameters...
04 May 2016 8,848 1 View
tank stiffener get yield and reach to failure before tank wall under static or dynamic load using Coupled Euler Lagrangian (CEL) method in abaqus
04 May 2016 8,395 4 View
" The option ‘boundarytype: displacement has been used; check status file between steps for warnings on any jumps prescribed across the steps in displacement values of translational dof. For...
02 March 2016 3,837 6 View
need to simulate “Elephant foot effect” or “Diamond effect” of large liquid storage tank in abaqus
02 March 2016 8,886 1 View
The ladder is running ok in the same gel. Is it a problem of loading dye? Or something wrong in the gel (but the ladder spread normally). I have previously measured the concentration and purity of...
09 October 2012 5,398 5 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I will be with my students collecting seaweed samples in a marine farm and later we will process this tissue for RNA isolation and further sequencing. Does anyone have tips on how to collect the...
04 August 2024 501 2 View
I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...
04 August 2024 9,913 7 View
I have been attempting to extract DNA from Bacterial, Fungal and Yeast banked samples (>1e7 cells) using Prepman Ultra reagent and I seem to be struggling to obtain a sequence. Although the...
01 August 2024 2,079 0 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am attempting to isolate picocyanobacteria from seawater (pre-filtered with a GF/D membrane) using the pour plate technique and filter plating method (Kearney et al., 2022) on Pro99 and SNAX...
30 July 2024 1,040 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View