How to run a program opensees Linux from python ?

08 September 2017 9,966 1 View

How to extract the desired signal from the following combination?

A given receiver has received the signals in the graph. It is aimed to extract the red signal. Is there an idea for that?

07 August 2017 9,393 1 View

When and why does nucleus engulf mitochondaria?

In our study using a herbal extract in a large dose, we found that the nucleus engulfs the mitochondria in cardiac myocyte of rat in a way similar to phagocytosis. All heart injury markers and...

11 December 2016 7,637 7 View

How to Extracts the maximum result from an Abaqus odb ??

i mean maximum result through all values during step time, is there any script in abaqus can do this ??

05 June 2016 1,268 0 View

In seismic analysis of tanks , are we have to consider parameters of cycle hardening in abaqus ??

in nonlinear analysis , what i do before is define only elastic and plastic stress vs strain and define fracture point value , yesterday i read this paper and found that there is also parameters...

04 May 2016 8,652 1 View

Is that really or it is error in modeling in abaqus?

tank stiffener get yield and reach to failure before tank wall under static or dynamic load using Coupled Euler Lagrangian (CEL) method in abaqus

04 May 2016 8,273 4 View

What is similar to Link element (LINK8) that was used in ANSYS to model the seismic isolation system in abaqus ??

model isolated tanks in abaqus

03 April 2016 7,376 2 View

What is the reason for that message in abaqus ??

02 March 2016 3,686 6 View

How to perform buckling analysis of a cylindrical shell with a fluid flow using Fluid Structure Interaction in abaqus ??

02 March 2016 8,770 1 View

What could be the cause of PCR product bands not moving from the well of the gel electrophoresis?

The ladder is running ok in the same gel. Is it a problem of loading dye? Or something wrong in the gel (but the ladder spread normally). I have previously measured the concentration and purity of...

09 October 2012 5,268 5 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View