Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

Sample modeling in ABAQUS software and its relationship with the real world?

About crack modeling in ABAQUS: Mode I (pure-tensile cracking) and Mode II (pure-shear cracking), these assumptions may be accruing in theoretical approach (ABAQUS) not practical in Lab....

19 February 2021 6,156 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

An article on the Iranian state's civil liability in the COVID-19 matter needs supervision; Is anyone interested in collaborating?

Hello. An article on the Iranian state's civil liability in the COVID-19 issue has been written in collaboration with a friend and a comparative look at law and biology. The article is ready to be...

15 February 2021 2,906 2 View

Inter-rater / inter-coder reliability for thematic analysis?

In my research, I have used metaphorical elicitation tasks to investigate learners' conceptualization of speaking fluency. In the analysis phase, I used thematic analysis to make themes out of...

10 February 2021 4,719 11 View

How to define two different phases with different species?

Hello all, I am trying to model CO2 being dissolved in a bubble column filled with water. For mass transfer definitions, I need to define two phases: for instance, liquid and gas, where the liquid...

08 February 2021 2,722 3 View

Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

What is the type or grade of ethanol used in SOL-GEL?

I'm preparing materials that will be use in SOL-GEL to produce silica gel, I will use Tetraethyl orthosilicate (TEOS) as precursor, and ethanol as solvent , but when I search to buy ethanol, the...

01 February 2021 5,153 4 View

Where to buy optically clear, low viscosity, refractive index 1.5-1.4 Silicone Oil ?

For research purposes, it is required to have optically clear, low viscosity silicone oil with a refractive index of 1.5-1.4. It is going to be used in optoelectronic research. Online purchase is...

01 February 2021 9,160 3 View

Can any one provide information about medicine, epidemic and critical issues or it is mandatory to be an expert ?

Due to the pandemic of coronavirus, the most source that the people depend on was social media. There is no guaranteed solution that is biased from political opinion. An example of that the...

01 February 2021 7,567 3 View

No title

02 March 2021 3,060 3 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View