Some of us use Streptavidin coated plates.
Please suggest a few trending and futuristic PhD Research Topics/ Gaps in Management (preferably in Service Quality / Quality Management) in Education (preferably in Higher Education) in India....
08 April 2024 3,664 3 View
I checked the nanodrop conc of the plasmid sample and it was 1000 something. I cleaned the platform and the upper arm got mistakenly lowered and it still measured the conc around 41.Could be due...
14 January 2024 8,323 6 View
If my plasmid doesn't have Ecor1 and sal1 but i need my plasmid to have those, I am aware that i can make primers with Ecor 1 and sal1 overhangs but how is that done from the beginning?
11 September 2023 2,510 3 View
Does it have something to do with the fact that ampicillin acts only after the cells divide and kanamycin resistance has something to do with the ribosomes and then it inhibits the translation? I...
29 August 2023 4,997 1 View
Sgv was constructed and maxiprepped. The conc was 1965 ng/ul and accidently a few drops of nuclease free water got spilled in it. Can I still use the same SGV plasmid for transfection or should I...
29 August 2023 9,351 5 View
I followed maxiprep protocol and the yield was as low as 5.9ng/ul. All the steps were followed and everything was taken care of. Is it because the cultures were a month old?
21 August 2023 2,773 5 View
How do we decide which transfection it is? Does it depend on whether we used PEI buffer or electroporation?
07 August 2023 782 5 View
We use Hind 111 is used almost every time but why? How many enzymes do we have to choose per experiment?
07 August 2023 8,175 2 View
Does it have something to do with the concentration?
03 August 2023 1,546 3 View
Why do we add media first and DMSO later?
02 August 2023 3,157 6 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 941 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,297 0 View
I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...
07 August 2024 2,283 2 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,105 4 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...
04 August 2024 5,227 4 View
In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...
01 August 2024 4,403 4 View
Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...
01 August 2024 2,250 2 View
Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...
01 August 2024 6,134 2 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,292 3 View