What are the necessary input data for MOS doping distribution with SILVACO ATHENA -ATLAS simulation?

More Abdulghefar Kamil Faiq's questions See All

Are you a specialist in the field of artificial neural networks?

Dear Sir I welcome all researchers specialized in the field of artificial neural networks to conduct joint research in this specialty and its applications in engineering and science. If you would...

24 June 2023 8,262 0 View

What is the difference between a covariate and a confounder?

what is the difference between a covariate and a confounder?

15 June 2023 6,970 3 View

JCR list of 2023?

Distinguished researchers and scientists, I hope you all are doing well. In which month of 2023 will the JCR impact factor and quartile ranking of journals be released? thanks

07 June 2023 4,117 2 View

How endonuklease restriction enzyme indentify mutation in gene?

about mutation

20 May 2023 3,238 2 View

Controls for ChIP-qPCR?

Hi everyone, I am in search for positive and negative controls for some of Histone marks for ChIP-qPCR in HUDEP cells. Can anybody help in this matter? Marks are: H3K27ac H3K27me3 H3K4me3...

12 March 2023 5,833 2 View

If a protein has low intracellular expression levels, it is likely that the amount of protein secreted into the extracellular space will also be low?

if a protein has low intracellular expression levels, it is likely that the amount of protein secreted into the extracellular space will also be low?

06 March 2023 6,731 6 View

If protein expression in blood was low (detected by western blot) and protein level in serum (detected by ELISA) was high? what dose it mean?

Good day, If protein expression in blood monocytes was low (detected by western blot) and protein level in serum (detected by ELISA) was high? what dose it mean? Note: the protein should not...

22 February 2023 8,504 6 View

If gene expression is low for specific gene, does this mean when I measure the serum level by ELISA of protein expressed by this gene it will be low?

if gene expression is low in specific diseases based on previous research, But when I measured the protein expressed by the same gene in blood of same disease by ELISA I found high serum level?...

21 February 2023 320 4 View

How to implemented COSMO solvation moddel in ORCA by manually?

so how to prepare input file in ORCA manually,but ORCA does not have the COSMO solvation Moddel.please help me

03 February 2023 6,198 1 View

Hello, dear scientists and researchers! What is the most effective method for obtaining the colony after bacterial transformation?

Is there any specific reason that we cannot get the transferred colonies? According to our methods and protocols, we have done all the procedures of bacterial transformation and used plasmid pUC19...

11 November 2022 6,102 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,066 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View