What are the advantages and disadvantages of different types of steam turbine seals?

19 July 2021 1 812 Report

This refers to the smooth, labyrinth, honeycomb and brush seals used in steam turbines. If you know some more types, information is also welcome.

Sajid Ahammed

i think the article attached will help you a lot to understand.

http://www.goine.cn/en/dt/841.html

Badges
Science topic

More Serhii А. Palkov's questions See All

Is it possible to predict the conformations of the molecule in the solution based on quantum-chemical calculations?

Hello, everyone and thanks for helping me. My question is: I have a metal complex that has several possible conformations. I need to calculate what conformation is the most plausible in different...

08 January 2021 831 3 View

HFSS / Radiation efficiency?

Hi! I'm new with HFSS. Could somebody tell how HFSS calculate radiation efficiency? In my project I have small value of reflection coefficient at the antenna input (s11 = - 15 dB), but difference...

26 April 2019 4,149 18 View

How can I measure the binding energy experimentally?

I have a wild-type enzyme 'Ewt' and few mutant forms of this enzyme ('Emut1-Emutn'), and I want to compare energy of binding (Gb) of a substrate 'S' to these enzymes. I know that binding energy...

04 October 2015 2,938 9 View

Can someone give advice on how to clear my confusion with IgE-binding sites prediction?

Dear colleagues, Currently I'm trying to predict probable IgE-binding regions in one of the allergenic proteins and reveal candidate residues for mutation in order to design a...

08 February 2015 429 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View