How we can modify gold electrode with graphene? What are advantages in using graphene based electrode for cell-based sensor?
I know about graphene based sensor advantages, but I don't know about cell-based sensors. can my answer be helpful?
Dear N. Kheirabadi
Could you tell me more about graphene based sensor advantages? If possible, could you send me by email: [email protected]
Thank you so much
Anh
I am using a microelectrode and breast cancer cell line (MDA-MB-231 and MCF-7). Could you share your protocol in coating the electrode surface to enhance cell adhesion? Which concentration of...
06 July 2014 669 1 View
I bought Laminin from Sigma which in solution with concentration 1mg/mL. I would like to dilute it. Could you tell me in which buffer can I dilute? Can I dilute in PBS? Thank you so much
06 July 2014 4,311 8 View
I would like to test the response of cancer cells (MDA and MCF7) on Cisplatin. I bought a bottle (15g) in powder. Could you tell me how should I dilute it? Which concentration should I use? How...
05 June 2014 7,998 7 View
I am using MDA-MB-231 and MCF7 for doing experiment. We have CO2 independent medium. Could you tell me how should I add other components (FBS, Glutamin/max, Penicillin, Insulin..). If I need 1ml...
02 March 2014 10,031 2 View
Do you have an experience in modifying gold electrode by nanowire? How we can modify gold electrode by ZnO or Au nanowire? Which type of nanowire is better for cell-based sensors?
09 October 2013 2,662 2 View
I would like to modify our gold electrode by GO or r-GO. Does anyone have any experience?
09 October 2013 2,020 7 View
I have electrode arrays and I would like to measure multichannel with SI 1260. Are you working with this machine? If you know, please help me.
07 August 2013 7,743 1 View
I have three electrodes: WE, CE and RE. How can I connect with SI 1260 to measure V1/V2?
02 March 2013 5,121 2 View
My system consists of two gold electrodes inside a microchannel (300 micrometer width and 50 micrometer height) covered by a medium for cells. The surface of electrodes is modified with SAM and...
01 February 2013 2,656 0 View
I modified my gold electrode by 11-mercaptoundecanoic acid (11-MUA) in ethanol solution 1mM in 18h. I would like to clean and remove this SAM layer to reuse the chips.
31 December 2012 6,067 8 View
I'm trying to find a DNA extraction method for fungi that does not require equipment and heating. Is there anyone who can suggest an alternative option? Thank you
08 August 2024 4,733 2 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...
05 August 2024 3,783 2 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,978 2 View
Hi all. As a beginner in ChIP-seq experiments, I hope you understand that the following questions might be somewhat basic. I am planning to perform ChIP-seq or MeDIP-seq analysis to investigate...
28 July 2024 6,938 1 View
I performed mmpbsa of protein-protein complex simulation on gromacs. My binding free energy is +166781. This complex is stable when experimentally produced in wet lab. In index.ndx I grouped...
19 July 2024 4,120 5 View
Hello all, I extracted RNA from my samples and performed RIP-seq. After annotating the genomic regions using R, I obtained promoters, exons, introns, and UTRs. Given that my samples consist of...
18 July 2024 1,579 2 View
I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...
16 July 2024 5,031 1 View