I have electrode arrays and I would like to measure multichannel with SI 1260. Are you working with this machine? If you know, please help me.
also for various techniques you can refer the book matrix preconditioning .... ..... by K E Chen, cambridge university press
best
I am using a microelectrode and breast cancer cell line (MDA-MB-231 and MCF-7). Could you share your protocol in coating the electrode surface to enhance cell adhesion? Which concentration of...
06 July 2014 669 1 View
I bought Laminin from Sigma which in solution with concentration 1mg/mL. I would like to dilute it. Could you tell me in which buffer can I dilute? Can I dilute in PBS? Thank you so much
06 July 2014 4,311 8 View
I would like to test the response of cancer cells (MDA and MCF7) on Cisplatin. I bought a bottle (15g) in powder. Could you tell me how should I dilute it? Which concentration should I use? How...
05 June 2014 7,998 7 View
I am using MDA-MB-231 and MCF7 for doing experiment. We have CO2 independent medium. Could you tell me how should I add other components (FBS, Glutamin/max, Penicillin, Insulin..). If I need 1ml...
02 March 2014 10,031 2 View
Do you have an experience in modifying gold electrode by nanowire? How we can modify gold electrode by ZnO or Au nanowire? Which type of nanowire is better for cell-based sensors?
09 October 2013 2,662 2 View
I would like to modify our gold electrode by GO or r-GO. Does anyone have any experience?
09 October 2013 2,020 7 View
How we can modify gold electrode with graphene? What are advantages in using graphene based electrode for cell-based sensor?
08 September 2013 9,131 2 View
I have three electrodes: WE, CE and RE. How can I connect with SI 1260 to measure V1/V2?
02 March 2013 5,121 2 View
My system consists of two gold electrodes inside a microchannel (300 micrometer width and 50 micrometer height) covered by a medium for cells. The surface of electrodes is modified with SAM and...
01 February 2013 2,656 0 View
I modified my gold electrode by 11-mercaptoundecanoic acid (11-MUA) in ethanol solution 1mM in 18h. I would like to clean and remove this SAM layer to reuse the chips.
31 December 2012 6,067 8 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I'm trying to find a DNA extraction method for fungi that does not require equipment and heating. Is there anyone who can suggest an alternative option? Thank you
08 August 2024 4,733 2 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...
03 August 2024 7,843 1 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...
31 July 2024 5,785 4 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View